more old autosaves go
This commit is contained in:
parent
d37a57244b
commit
bba95d2a5d
|
|
@ -1,339 +0,0 @@
|
|||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
[printer]
|
||||
max_velocity: 150
|
||||
max_accel: 500
|
||||
max_accel_to_decel: 500
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 20
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "false"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 100
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
#control: pid
|
||||
#pid_kp: 28.413
|
||||
#pid_ki: 1.334
|
||||
#pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 28,21
|
||||
mesh_max:465,460
|
||||
probe_count: 10,10
|
||||
fade_start: 5.0
|
||||
fade_end: 100.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.940
|
||||
#*#
|
||||
#*# [bed_mesh vcore]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.146250, -0.580313, -0.993438, -1.390000, -1.680625
|
||||
#*# 0.458125, -0.109688, -0.498750, -0.825938, -1.111250
|
||||
#*# 0.674375, 0.189687, -0.035313, -0.261250, -0.505000
|
||||
#*# 1.180937, 0.899687, 0.665000, 0.499375, 0.222500
|
||||
#*# 2.068437, 1.804375, 1.605000, 1.387500, 1.222187
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.639062, 0.424687, 0.258437, 0.241875, 0.230312, 0.246875, 0.328125, 0.414062, 0.500625, 0.680000
|
||||
#*# 0.564687, 0.393125, 0.277812, 0.231875, 0.185312, 0.231250, 0.281875, 0.411250, 0.548437, 0.672812
|
||||
#*# 0.420625, 0.269687, 0.158125, 0.149062, 0.135625, 0.183437, 0.253437, 0.372187, 0.493750, 0.635625
|
||||
#*# 0.261562, 0.093125, 0.050937, 0.038125, 0.081562, 0.124062, 0.225625, 0.337500, 0.458125, 0.671875
|
||||
#*# 0.072187, 0.003750, -0.058750, -0.050938, 0.008125, 0.077812, 0.234375, 0.315312, 0.470312, 0.645312
|
||||
#*# -0.024688, -0.101250, -0.121250, -0.080625, -0.048438, 0.078437, 0.175312, 0.323437, 0.460000, 0.666250
|
||||
#*# -0.021563, -0.035313, -0.082500, -0.036875, 0.003125, 0.100312, 0.242500, 0.379687, 0.519062, 0.723437
|
||||
#*# 0.054062, 0.006250, 0.014062, 0.055625, 0.117500, 0.200937, 0.335312, 0.489062, 0.647500, 0.789062
|
||||
#*# 0.137187, 0.130625, 0.120312, 0.160000, 0.248750, 0.358125, 0.451250, 0.552812, 0.729687, 0.897187
|
||||
#*# 0.296562, 0.284062, 0.302500, 0.377187, 0.430000, 0.519062, 0.624687, 0.718750, 0.899687, 1.069687
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 28.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 10
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 21.0
|
||||
#*# x_count = 10
|
||||
#*# max_y = 459.93
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.95
|
||||
#*#
|
||||
#*# [bed_mesh ratos]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.658750, 0.348437, 0.369062, 0.392500, 0.536250
|
||||
#*# 0.306562, 0.168125, 0.214375, 0.328750, 0.452812
|
||||
#*# -0.138750, -0.135625, 0.045312, 0.248125, 0.420000
|
||||
#*# -0.223750, -0.061875, 0.141250, 0.383437, 0.531250
|
||||
#*# 0.079375, 0.220000, 0.478750, 0.668750, -0.534063
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 19.616
|
||||
#*# pid_ki = 0.844
|
||||
#*# pid_kd = 114.017
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.455
|
||||
#*# pid_ki = 1.659
|
||||
#*# pid_kd = 626.020
|
||||
|
|
@ -1,339 +0,0 @@
|
|||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
[printer]
|
||||
max_velocity: 150
|
||||
max_accel: 500
|
||||
max_accel_to_decel: 500
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 20
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "false"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 100
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
#control: pid
|
||||
#pid_kp: 28.413
|
||||
#pid_ki: 1.334
|
||||
#pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 28,21
|
||||
mesh_max:465,460
|
||||
probe_count: 10,10
|
||||
fade_start: 5.0
|
||||
fade_end: 100.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.940
|
||||
#*#
|
||||
#*# [bed_mesh vcore]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.146250, -0.580313, -0.993438, -1.390000, -1.680625
|
||||
#*# 0.458125, -0.109688, -0.498750, -0.825938, -1.111250
|
||||
#*# 0.674375, 0.189687, -0.035313, -0.261250, -0.505000
|
||||
#*# 1.180937, 0.899687, 0.665000, 0.499375, 0.222500
|
||||
#*# 2.068437, 1.804375, 1.605000, 1.387500, 1.222187
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.639062, 0.424687, 0.258437, 0.241875, 0.230312, 0.246875, 0.328125, 0.414062, 0.500625, 0.680000
|
||||
#*# 0.564687, 0.393125, 0.277812, 0.231875, 0.185312, 0.231250, 0.281875, 0.411250, 0.548437, 0.672812
|
||||
#*# 0.420625, 0.269687, 0.158125, 0.149062, 0.135625, 0.183437, 0.253437, 0.372187, 0.493750, 0.635625
|
||||
#*# 0.261562, 0.093125, 0.050937, 0.038125, 0.081562, 0.124062, 0.225625, 0.337500, 0.458125, 0.671875
|
||||
#*# 0.072187, 0.003750, -0.058750, -0.050938, 0.008125, 0.077812, 0.234375, 0.315312, 0.470312, 0.645312
|
||||
#*# -0.024688, -0.101250, -0.121250, -0.080625, -0.048438, 0.078437, 0.175312, 0.323437, 0.460000, 0.666250
|
||||
#*# -0.021563, -0.035313, -0.082500, -0.036875, 0.003125, 0.100312, 0.242500, 0.379687, 0.519062, 0.723437
|
||||
#*# 0.054062, 0.006250, 0.014062, 0.055625, 0.117500, 0.200937, 0.335312, 0.489062, 0.647500, 0.789062
|
||||
#*# 0.137187, 0.130625, 0.120312, 0.160000, 0.248750, 0.358125, 0.451250, 0.552812, 0.729687, 0.897187
|
||||
#*# 0.296562, 0.284062, 0.302500, 0.377187, 0.430000, 0.519062, 0.624687, 0.718750, 0.899687, 1.069687
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 28.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 10
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 21.0
|
||||
#*# x_count = 10
|
||||
#*# max_y = 459.93
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.95
|
||||
#*#
|
||||
#*# [bed_mesh ratos]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.658750, 0.348437, 0.369062, 0.392500, 0.536250
|
||||
#*# 0.306562, 0.168125, 0.214375, 0.328750, 0.452812
|
||||
#*# -0.138750, -0.135625, 0.045312, 0.248125, 0.420000
|
||||
#*# -0.223750, -0.061875, 0.141250, 0.383437, 0.531250
|
||||
#*# 0.079375, 0.220000, 0.478750, 0.668750, -0.534063
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 19.661
|
||||
#*# pid_ki = 0.819
|
||||
#*# pid_kd = 117.969
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.455
|
||||
#*# pid_ki = 1.659
|
||||
#*# pid_kd = 626.020
|
||||
|
|
@ -1,339 +0,0 @@
|
|||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
[printer]
|
||||
max_velocity: 150
|
||||
max_accel: 500
|
||||
max_accel_to_decel: 500
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 20
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "false"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 100
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
#control: pid
|
||||
#pid_kp: 28.413
|
||||
#pid_ki: 1.334
|
||||
#pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 28,21
|
||||
mesh_max:465,460
|
||||
probe_count: 10,10
|
||||
fade_start: 5.0
|
||||
fade_end: 100.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.940
|
||||
#*#
|
||||
#*# [bed_mesh vcore]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.146250, -0.580313, -0.993438, -1.390000, -1.680625
|
||||
#*# 0.458125, -0.109688, -0.498750, -0.825938, -1.111250
|
||||
#*# 0.674375, 0.189687, -0.035313, -0.261250, -0.505000
|
||||
#*# 1.180937, 0.899687, 0.665000, 0.499375, 0.222500
|
||||
#*# 2.068437, 1.804375, 1.605000, 1.387500, 1.222187
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.555625, 0.374687, 0.219375, 0.202187, 0.221250, 0.264687, 0.364687, 0.525312, 0.640625, 0.882812
|
||||
#*# 0.490625, 0.334687, 0.227187, 0.208125, 0.215312, 0.274687, 0.377500, 0.548437, 0.687187, 0.871250
|
||||
#*# 0.340000, 0.206562, 0.115000, 0.139375, 0.154375, 0.215625, 0.356250, 0.515312, 0.670000, 0.864062
|
||||
#*# 0.168125, 0.039375, 0.020937, 0.058125, 0.089687, 0.185000, 0.305937, 0.470000, 0.631562, 0.887500
|
||||
#*# 0.013750, -0.047813, -0.088750, -0.050625, 0.032812, 0.153750, 0.345625, 0.444687, 0.649062, 0.867500
|
||||
#*# -0.098125, -0.149063, -0.131563, -0.085938, 0.000625, 0.120312, 0.263125, 0.438437, 0.633437, 0.862187
|
||||
#*# -0.115000, -0.095938, -0.125313, -0.055625, 0.027187, 0.160312, 0.315937, 0.489062, 0.676562, 0.934062
|
||||
#*# -0.026563, -0.060625, -0.026250, 0.030625, 0.114062, 0.254062, 0.394062, 0.587500, 0.780625, 0.999375
|
||||
#*# 0.044062, 0.048437, 0.049687, 0.122187, 0.280312, 0.400312, 0.502187, 0.670625, 0.852500, 1.084687
|
||||
#*# 0.176250, 0.179062, 0.227812, 0.314687, 0.387187, 0.512500, 0.648125, 0.784687, 1.009375, 1.224375
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 28.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 10
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 21.0
|
||||
#*# x_count = 10
|
||||
#*# max_y = 459.93
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.95
|
||||
#*#
|
||||
#*# [bed_mesh ratos]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.658750, 0.348437, 0.369062, 0.392500, 0.536250
|
||||
#*# 0.306562, 0.168125, 0.214375, 0.328750, 0.452812
|
||||
#*# -0.138750, -0.135625, 0.045312, 0.248125, 0.420000
|
||||
#*# -0.223750, -0.061875, 0.141250, 0.383437, 0.531250
|
||||
#*# 0.079375, 0.220000, 0.478750, 0.668750, -0.534063
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 19.661
|
||||
#*# pid_ki = 0.819
|
||||
#*# pid_kd = 117.969
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.455
|
||||
#*# pid_ki = 1.659
|
||||
#*# pid_kd = 626.020
|
||||
|
|
@ -1,339 +0,0 @@
|
|||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
[printer]
|
||||
max_velocity: 150
|
||||
max_accel: 500
|
||||
max_accel_to_decel: 500
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 20
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "false"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 100
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
#control: pid
|
||||
#pid_kp: 28.413
|
||||
#pid_ki: 1.334
|
||||
#pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 28,21
|
||||
mesh_max:465,460
|
||||
probe_count: 10,10
|
||||
fade_start: 5.0
|
||||
fade_end: 100.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.940
|
||||
#*#
|
||||
#*# [bed_mesh vcore]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.146250, -0.580313, -0.993438, -1.390000, -1.680625
|
||||
#*# 0.458125, -0.109688, -0.498750, -0.825938, -1.111250
|
||||
#*# 0.674375, 0.189687, -0.035313, -0.261250, -0.505000
|
||||
#*# 1.180937, 0.899687, 0.665000, 0.499375, 0.222500
|
||||
#*# 2.068437, 1.804375, 1.605000, 1.387500, 1.222187
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.533437, 0.361250, 0.195625, 0.148125, 0.168437, 0.198750, 0.254375, 0.394687, 0.470000, 0.663750
|
||||
#*# 0.464375, 0.308125, 0.186250, 0.162187, 0.154062, 0.194687, 0.283750, 0.416562, 0.533437, 0.690625
|
||||
#*# 0.335625, 0.186562, 0.084375, 0.101875, 0.095625, 0.139687, 0.255625, 0.379062, 0.492812, 0.649375
|
||||
#*# 0.163125, 0.040312, -0.005000, 0.029062, 0.036250, 0.114687, 0.214062, 0.336875, 0.463125, 0.666250
|
||||
#*# 0.022500, -0.036875, -0.090938, -0.067813, -0.002188, 0.077500, 0.226250, 0.311562, 0.481250, 0.674062
|
||||
#*# -0.065625, -0.113438, -0.108750, -0.085000, -0.002813, 0.085625, 0.188750, 0.347187, 0.504375, 0.694687
|
||||
#*# -0.044375, -0.024375, -0.064375, -0.008125, 0.058750, 0.168437, 0.275000, 0.425937, 0.577812, 0.791562
|
||||
#*# 0.070000, 0.032187, 0.065000, 0.100000, 0.171875, 0.293437, 0.395625, 0.556250, 0.718125, 0.880312
|
||||
#*# 0.168750, 0.176562, 0.175937, 0.230937, 0.366250, 0.462812, 0.555000, 0.686562, 0.813437, 0.993125
|
||||
#*# 0.335312, 0.349375, 0.385000, 0.460312, 0.522187, 0.619062, 0.747500, 0.842187, 1.026250, 1.203125
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 28.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 10
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 21.0
|
||||
#*# x_count = 10
|
||||
#*# max_y = 459.93
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.95
|
||||
#*#
|
||||
#*# [bed_mesh ratos]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.658750, 0.348437, 0.369062, 0.392500, 0.536250
|
||||
#*# 0.306562, 0.168125, 0.214375, 0.328750, 0.452812
|
||||
#*# -0.138750, -0.135625, 0.045312, 0.248125, 0.420000
|
||||
#*# -0.223750, -0.061875, 0.141250, 0.383437, 0.531250
|
||||
#*# 0.079375, 0.220000, 0.478750, 0.668750, -0.534063
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 19.661
|
||||
#*# pid_ki = 0.819
|
||||
#*# pid_kd = 117.969
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.455
|
||||
#*# pid_ki = 1.659
|
||||
#*# pid_kd = 626.020
|
||||
|
|
@ -1,339 +0,0 @@
|
|||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
[printer]
|
||||
max_velocity: 150
|
||||
max_accel: 500
|
||||
max_accel_to_decel: 500
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 20
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "false"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 100
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
#control: pid
|
||||
#pid_kp: 28.413
|
||||
#pid_ki: 1.334
|
||||
#pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 28,21
|
||||
mesh_max:465,460
|
||||
probe_count: 10,10
|
||||
fade_start: 5.0
|
||||
fade_end: 100.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.900
|
||||
#*#
|
||||
#*# [bed_mesh vcore]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.146250, -0.580313, -0.993438, -1.390000, -1.680625
|
||||
#*# 0.458125, -0.109688, -0.498750, -0.825938, -1.111250
|
||||
#*# 0.674375, 0.189687, -0.035313, -0.261250, -0.505000
|
||||
#*# 1.180937, 0.899687, 0.665000, 0.499375, 0.222500
|
||||
#*# 2.068437, 1.804375, 1.605000, 1.387500, 1.222187
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.533437, 0.361250, 0.195625, 0.148125, 0.168437, 0.198750, 0.254375, 0.394687, 0.470000, 0.663750
|
||||
#*# 0.464375, 0.308125, 0.186250, 0.162187, 0.154062, 0.194687, 0.283750, 0.416562, 0.533437, 0.690625
|
||||
#*# 0.335625, 0.186562, 0.084375, 0.101875, 0.095625, 0.139687, 0.255625, 0.379062, 0.492812, 0.649375
|
||||
#*# 0.163125, 0.040312, -0.005000, 0.029062, 0.036250, 0.114687, 0.214062, 0.336875, 0.463125, 0.666250
|
||||
#*# 0.022500, -0.036875, -0.090938, -0.067813, -0.002188, 0.077500, 0.226250, 0.311562, 0.481250, 0.674062
|
||||
#*# -0.065625, -0.113438, -0.108750, -0.085000, -0.002813, 0.085625, 0.188750, 0.347187, 0.504375, 0.694687
|
||||
#*# -0.044375, -0.024375, -0.064375, -0.008125, 0.058750, 0.168437, 0.275000, 0.425937, 0.577812, 0.791562
|
||||
#*# 0.070000, 0.032187, 0.065000, 0.100000, 0.171875, 0.293437, 0.395625, 0.556250, 0.718125, 0.880312
|
||||
#*# 0.168750, 0.176562, 0.175937, 0.230937, 0.366250, 0.462812, 0.555000, 0.686562, 0.813437, 0.993125
|
||||
#*# 0.335312, 0.349375, 0.385000, 0.460312, 0.522187, 0.619062, 0.747500, 0.842187, 1.026250, 1.203125
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 28.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 10
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 21.0
|
||||
#*# x_count = 10
|
||||
#*# max_y = 459.93
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.95
|
||||
#*#
|
||||
#*# [bed_mesh ratos]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.658750, 0.348437, 0.369062, 0.392500, 0.536250
|
||||
#*# 0.306562, 0.168125, 0.214375, 0.328750, 0.452812
|
||||
#*# -0.138750, -0.135625, 0.045312, 0.248125, 0.420000
|
||||
#*# -0.223750, -0.061875, 0.141250, 0.383437, 0.531250
|
||||
#*# 0.079375, 0.220000, 0.478750, 0.668750, -0.534063
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 19.661
|
||||
#*# pid_ki = 0.819
|
||||
#*# pid_kd = 117.969
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.455
|
||||
#*# pid_ki = 1.659
|
||||
#*# pid_kd = 626.020
|
||||
|
|
@ -1,339 +0,0 @@
|
|||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
[printer]
|
||||
max_velocity: 150
|
||||
max_accel: 500
|
||||
max_accel_to_decel: 500
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 20
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "false"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 100
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
#control: pid
|
||||
#pid_kp: 28.413
|
||||
#pid_ki: 1.334
|
||||
#pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 28,21
|
||||
mesh_max:465,460
|
||||
probe_count: 10,10
|
||||
fade_start: 5.0
|
||||
fade_end: 100.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.920
|
||||
#*#
|
||||
#*# [bed_mesh vcore]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.146250, -0.580313, -0.993438, -1.390000, -1.680625
|
||||
#*# 0.458125, -0.109688, -0.498750, -0.825938, -1.111250
|
||||
#*# 0.674375, 0.189687, -0.035313, -0.261250, -0.505000
|
||||
#*# 1.180937, 0.899687, 0.665000, 0.499375, 0.222500
|
||||
#*# 2.068437, 1.804375, 1.605000, 1.387500, 1.222187
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.533437, 0.361250, 0.195625, 0.148125, 0.168437, 0.198750, 0.254375, 0.394687, 0.470000, 0.663750
|
||||
#*# 0.464375, 0.308125, 0.186250, 0.162187, 0.154062, 0.194687, 0.283750, 0.416562, 0.533437, 0.690625
|
||||
#*# 0.335625, 0.186562, 0.084375, 0.101875, 0.095625, 0.139687, 0.255625, 0.379062, 0.492812, 0.649375
|
||||
#*# 0.163125, 0.040312, -0.005000, 0.029062, 0.036250, 0.114687, 0.214062, 0.336875, 0.463125, 0.666250
|
||||
#*# 0.022500, -0.036875, -0.090938, -0.067813, -0.002188, 0.077500, 0.226250, 0.311562, 0.481250, 0.674062
|
||||
#*# -0.065625, -0.113438, -0.108750, -0.085000, -0.002813, 0.085625, 0.188750, 0.347187, 0.504375, 0.694687
|
||||
#*# -0.044375, -0.024375, -0.064375, -0.008125, 0.058750, 0.168437, 0.275000, 0.425937, 0.577812, 0.791562
|
||||
#*# 0.070000, 0.032187, 0.065000, 0.100000, 0.171875, 0.293437, 0.395625, 0.556250, 0.718125, 0.880312
|
||||
#*# 0.168750, 0.176562, 0.175937, 0.230937, 0.366250, 0.462812, 0.555000, 0.686562, 0.813437, 0.993125
|
||||
#*# 0.335312, 0.349375, 0.385000, 0.460312, 0.522187, 0.619062, 0.747500, 0.842187, 1.026250, 1.203125
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 28.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 10
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 21.0
|
||||
#*# x_count = 10
|
||||
#*# max_y = 459.93
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.95
|
||||
#*#
|
||||
#*# [bed_mesh ratos]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.658750, 0.348437, 0.369062, 0.392500, 0.536250
|
||||
#*# 0.306562, 0.168125, 0.214375, 0.328750, 0.452812
|
||||
#*# -0.138750, -0.135625, 0.045312, 0.248125, 0.420000
|
||||
#*# -0.223750, -0.061875, 0.141250, 0.383437, 0.531250
|
||||
#*# 0.079375, 0.220000, 0.478750, 0.668750, -0.534063
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 19.661
|
||||
#*# pid_ki = 0.819
|
||||
#*# pid_kd = 117.969
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.455
|
||||
#*# pid_ki = 1.659
|
||||
#*# pid_kd = 626.020
|
||||
|
|
@ -1,339 +0,0 @@
|
|||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
[printer]
|
||||
max_velocity: 150
|
||||
max_accel: 500
|
||||
max_accel_to_decel: 500
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 20
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "false"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 100
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
#control: pid
|
||||
#pid_kp: 28.413
|
||||
#pid_ki: 1.334
|
||||
#pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 28,21
|
||||
mesh_max:465,460
|
||||
probe_count: 10,10
|
||||
fade_start: 5.0
|
||||
fade_end: 100.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.920
|
||||
#*#
|
||||
#*# [bed_mesh vcore]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.146250, -0.580313, -0.993438, -1.390000, -1.680625
|
||||
#*# 0.458125, -0.109688, -0.498750, -0.825938, -1.111250
|
||||
#*# 0.674375, 0.189687, -0.035313, -0.261250, -0.505000
|
||||
#*# 1.180937, 0.899687, 0.665000, 0.499375, 0.222500
|
||||
#*# 2.068437, 1.804375, 1.605000, 1.387500, 1.222187
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.530312, 0.340000, 0.180000, 0.161562, 0.163125, 0.175312, 0.245625, 0.368437, 0.451562, 0.653750
|
||||
#*# 0.456875, 0.302500, 0.200625, 0.161875, 0.153437, 0.191875, 0.273750, 0.410312, 0.509375, 0.651875
|
||||
#*# 0.323750, 0.186562, 0.094375, 0.106562, 0.100937, 0.139375, 0.236875, 0.364062, 0.485312, 0.633437
|
||||
#*# 0.159687, 0.031250, 0.007812, 0.027187, 0.054375, 0.119687, 0.218437, 0.335312, 0.455312, 0.665937
|
||||
#*# 0.010312, -0.039688, -0.084688, -0.067813, 0.000937, 0.083125, 0.238750, 0.308750, 0.482187, 0.664375
|
||||
#*# -0.073438, -0.126250, -0.118125, -0.082188, -0.012500, 0.093125, 0.198125, 0.351875, 0.498437, 0.700937
|
||||
#*# -0.060625, -0.040625, -0.083750, -0.020625, 0.054375, 0.149062, 0.275937, 0.416875, 0.575000, 0.769062
|
||||
#*# 0.038125, -0.002188, 0.034062, 0.079687, 0.148437, 0.266562, 0.369687, 0.531562, 0.687812, 0.840937
|
||||
#*# 0.138437, 0.157187, 0.149062, 0.205625, 0.329375, 0.438750, 0.541250, 0.646875, 0.778437, 0.958125
|
||||
#*# 0.310312, 0.318750, 0.352500, 0.425312, 0.496250, 0.581562, 0.707187, 0.804687, 0.983437, 1.161250
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 28.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 10
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 21.0
|
||||
#*# x_count = 10
|
||||
#*# max_y = 459.93
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.95
|
||||
#*#
|
||||
#*# [bed_mesh ratos]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.658750, 0.348437, 0.369062, 0.392500, 0.536250
|
||||
#*# 0.306562, 0.168125, 0.214375, 0.328750, 0.452812
|
||||
#*# -0.138750, -0.135625, 0.045312, 0.248125, 0.420000
|
||||
#*# -0.223750, -0.061875, 0.141250, 0.383437, 0.531250
|
||||
#*# 0.079375, 0.220000, 0.478750, 0.668750, -0.534063
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 19.661
|
||||
#*# pid_ki = 0.819
|
||||
#*# pid_kd = 117.969
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.455
|
||||
#*# pid_ki = 1.659
|
||||
#*# pid_kd = 626.020
|
||||
|
|
@ -1,339 +0,0 @@
|
|||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
[printer]
|
||||
max_velocity: 150
|
||||
max_accel: 500
|
||||
max_accel_to_decel: 500
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 20
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "false"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 100
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
#control: pid
|
||||
#pid_kp: 28.413
|
||||
#pid_ki: 1.334
|
||||
#pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 20,20
|
||||
mesh_max:465,460
|
||||
probe_count: 10,10
|
||||
fade_start: 1.0
|
||||
fade_end: 100.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.920
|
||||
#*#
|
||||
#*# [bed_mesh vcore]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.146250, -0.580313, -0.993438, -1.390000, -1.680625
|
||||
#*# 0.458125, -0.109688, -0.498750, -0.825938, -1.111250
|
||||
#*# 0.674375, 0.189687, -0.035313, -0.261250, -0.505000
|
||||
#*# 1.180937, 0.899687, 0.665000, 0.499375, 0.222500
|
||||
#*# 2.068437, 1.804375, 1.605000, 1.387500, 1.222187
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.588437, 0.368437, 0.182187, 0.106250, 0.136250, 0.152500, 0.219687, 0.321875, 0.426250, 0.597812
|
||||
#*# 0.545937, 0.339375, 0.202187, 0.170625, 0.113125, 0.175000, 0.264687, 0.386875, 0.513437, 0.657187
|
||||
#*# 0.407812, 0.231875, 0.102812, 0.080000, 0.091875, 0.130625, 0.244375, 0.365937, 0.492187, 0.658125
|
||||
#*# 0.250937, 0.111875, 0.023125, 0.023125, 0.030625, 0.112187, 0.215000, 0.338750, 0.486875, 0.688437
|
||||
#*# 0.115625, 0.022812, -0.068438, -0.046250, 0.004062, 0.083437, 0.230000, 0.326562, 0.493750, 0.685625
|
||||
#*# 0.010000, -0.061875, -0.088750, -0.070938, -0.022500, 0.067500, 0.183125, 0.338437, 0.497812, 0.709375
|
||||
#*# 0.013750, 0.005000, -0.038438, -0.002188, 0.006250, 0.129375, 0.256562, 0.409062, 0.565937, 0.793750
|
||||
#*# 0.104062, 0.036875, 0.043437, 0.034062, 0.121562, 0.209062, 0.368125, 0.503437, 0.684687, 0.850937
|
||||
#*# 0.206562, 0.147187, 0.153125, 0.180625, 0.317812, 0.397500, 0.490312, 0.622187, 0.747500, 0.971875
|
||||
#*# 0.348125, 0.305937, 0.296875, 0.390625, 0.445000, 0.532187, 0.655937, 0.772500, 0.942500, 1.139062
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 28.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 10
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 21.0
|
||||
#*# x_count = 10
|
||||
#*# max_y = 459.93
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.95
|
||||
#*#
|
||||
#*# [bed_mesh ratos]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.658750, 0.348437, 0.369062, 0.392500, 0.536250
|
||||
#*# 0.306562, 0.168125, 0.214375, 0.328750, 0.452812
|
||||
#*# -0.138750, -0.135625, 0.045312, 0.248125, 0.420000
|
||||
#*# -0.223750, -0.061875, 0.141250, 0.383437, 0.531250
|
||||
#*# 0.079375, 0.220000, 0.478750, 0.668750, -0.534063
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 19.661
|
||||
#*# pid_ki = 0.819
|
||||
#*# pid_kd = 117.969
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.455
|
||||
#*# pid_ki = 1.659
|
||||
#*# pid_kd = 626.020
|
||||
|
|
@ -1,301 +0,0 @@
|
|||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
[printer]
|
||||
max_velocity: 150
|
||||
max_accel: 500
|
||||
max_accel_to_decel: 500
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 20
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "false"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 100
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
#control: pid
|
||||
#pid_kp: 28.413
|
||||
#pid_ki: 1.334
|
||||
#pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 10,10
|
||||
mesh_max:465,460
|
||||
probe_count: 10,10
|
||||
fade_start: 1.0
|
||||
fade_end: 100.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.920
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.610000, 0.369062, 0.203750, 0.143750, 0.094375, 0.174687, 0.204687, 0.328437, 0.450937, 0.619687
|
||||
#*# 0.560937, 0.357187, 0.215000, 0.171875, 0.175312, 0.167812, 0.285937, 0.383437, 0.499375, 0.646562
|
||||
#*# 0.418125, 0.245937, 0.129687, 0.089062, 0.087500, 0.156562, 0.248125, 0.323750, 0.469062, 0.651250
|
||||
#*# 0.219375, 0.128437, 0.032812, 0.008125, 0.070000, 0.090000, 0.186250, 0.316250, 0.455000, 0.680000
|
||||
#*# 0.120625, -0.008125, -0.040625, -0.050313, -0.001563, 0.067500, 0.205937, 0.342500, 0.468750, 0.677500
|
||||
#*# 0.032500, -0.090000, -0.085000, -0.105938, -0.019375, 0.033437, 0.169062, 0.325000, 0.478750, 0.736875
|
||||
#*# 0.017500, -0.001563, -0.038750, -0.021875, 0.037500, 0.102812, 0.276875, 0.433750, 0.566250, 0.766250
|
||||
#*# 0.050000, 0.050625, 0.038437, 0.083437, 0.122187, 0.238437, 0.395937, 0.511562, 0.652187, 0.850000
|
||||
#*# 0.203437, 0.202812, 0.165937, 0.198437, 0.304062, 0.391562, 0.520625, 0.620000, 0.783437, 0.965625
|
||||
#*# 0.359687, 0.325937, 0.320000, 0.398750, 0.435937, 0.562500, 0.676250, 0.793437, 0.935937, 1.135625
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 20.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 10
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 20.0
|
||||
#*# x_count = 10
|
||||
#*# max_y = 459.92
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.96
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 19.661
|
||||
#*# pid_ki = 0.819
|
||||
#*# pid_kd = 117.969
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.455
|
||||
#*# pid_ki = 1.659
|
||||
#*# pid_kd = 626.020
|
||||
|
|
@ -1,301 +0,0 @@
|
|||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
[printer]
|
||||
max_velocity: 150
|
||||
max_accel: 500
|
||||
max_accel_to_decel: 500
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 20
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "false"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 100
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
#control: pid
|
||||
#pid_kp: 28.413
|
||||
#pid_ki: 1.334
|
||||
#pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 15,15
|
||||
mesh_max:465,460
|
||||
probe_count: 28,13
|
||||
fade_start: 1.0
|
||||
fade_end: 100.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.920
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.745312, 0.458750, 0.283437, 0.194687, 0.239375, 0.210937, 0.257187, 0.372187, 0.482187, 0.659375
|
||||
#*# 0.672812, 0.441875, 0.291250, 0.217812, 0.202187, 0.248750, 0.294062, 0.371250, 0.527187, 0.690937
|
||||
#*# 0.539375, 0.319687, 0.200000, 0.155312, 0.120312, 0.171250, 0.255937, 0.363437, 0.482500, 0.675625
|
||||
#*# 0.342187, 0.166875, 0.073437, 0.061562, 0.074375, 0.117812, 0.199062, 0.352187, 0.477500, 0.665937
|
||||
#*# 0.180000, 0.059375, -0.040938, -0.042500, 0.006250, 0.105000, 0.179687, 0.345625, 0.455625, 0.671875
|
||||
#*# 0.049687, -0.077813, -0.097188, -0.092500, -0.045000, 0.051250, 0.196250, 0.315937, 0.484062, 0.673750
|
||||
#*# 0.016250, -0.032813, -0.083438, -0.085313, -0.014688, 0.080312, 0.238437, 0.404687, 0.521562, 0.749375
|
||||
#*# 0.052500, 0.023750, -0.018750, 0.024687, 0.070937, 0.190000, 0.309687, 0.424062, 0.596562, 0.766875
|
||||
#*# 0.175937, 0.132187, 0.120000, 0.159687, 0.231562, 0.354062, 0.463750, 0.571875, 0.716562, 0.922500
|
||||
#*# 0.290000, 0.247187, 0.252500, 0.302187, 0.420312, 0.480625, 0.606875, 0.680312, 0.849687, 1.054062
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 10.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 10
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 10.0
|
||||
#*# x_count = 10
|
||||
#*# max_y = 460.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.95
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 19.661
|
||||
#*# pid_ki = 0.819
|
||||
#*# pid_kd = 117.969
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.455
|
||||
#*# pid_ki = 1.659
|
||||
#*# pid_kd = 626.020
|
||||
|
|
@ -1,304 +0,0 @@
|
|||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
[printer]
|
||||
max_velocity: 150
|
||||
max_accel: 500
|
||||
max_accel_to_decel: 500
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 20
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "false"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 100
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
#control: pid
|
||||
#pid_kp: 28.413
|
||||
#pid_ki: 1.334
|
||||
#pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 15,15
|
||||
mesh_max:465,460
|
||||
probe_count: 28,13
|
||||
fade_start: 1.0
|
||||
fade_end: 100.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.920
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.701250, 0.591250, 0.491562, 0.383750, 0.387187, 0.284062, 0.230000, 0.199062, 0.156562, 0.186562, 0.155937, 0.129687, 0.150625, 0.163750, 0.163750, 0.177500, 0.191250, 0.198125, 0.230000, 0.266250, 0.299375, 0.333750, 0.392187, 0.424687, 0.464687, 0.534687, 0.570312, 0.655000
|
||||
#*# 0.690625, 0.563437, 0.480000, 0.439687, 0.355937, 0.295937, 0.280312, 0.220937, 0.219375, 0.180000, 0.186562, 0.163437, 0.185625, 0.205937, 0.185312, 0.204062, 0.193125, 0.233125, 0.267500, 0.310625, 0.367187, 0.371875, 0.440937, 0.465000, 0.541250, 0.538750, 0.651250, 0.677500
|
||||
#*# 0.620625, 0.543750, 0.437812, 0.336250, 0.314062, 0.277812, 0.245625, 0.212187, 0.185000, 0.184062, 0.170312, 0.138125, 0.175625, 0.172187, 0.194062, 0.192812, 0.207812, 0.246562, 0.296875, 0.311875, 0.337812, 0.370937, 0.428125, 0.465625, 0.534062, 0.606562, 0.642500, 0.700625
|
||||
#*# 0.495625, 0.405000, 0.340625, 0.296562, 0.235312, 0.184062, 0.170937, 0.140937, 0.113125, 0.126875, 0.115000, 0.122812, 0.102187, 0.126875, 0.126250, 0.136562, 0.171562, 0.221562, 0.228750, 0.280312, 0.320312, 0.369687, 0.391562, 0.479687, 0.465937, 0.572500, 0.613750, 0.735625
|
||||
#*# 0.335000, 0.258437, 0.224687, 0.195000, 0.129062, 0.067187, 0.056875, 0.087500, 0.060312, 0.045937, 0.059687, 0.100312, 0.066875, 0.070937, 0.123750, 0.110312, 0.135000, 0.205625, 0.222500, 0.263125, 0.323125, 0.370000, 0.409062, 0.438437, 0.496562, 0.563437, 0.640937, 0.720937
|
||||
#*# 0.256250, 0.188750, 0.112812, 0.101250, 0.071875, 0.020625, 0.013750, 0.015937, -0.018438, 0.025000, 0.020625, 0.052187, 0.076875, 0.080937, 0.112500, 0.120312, 0.145312, 0.161875, 0.258437, 0.263125, 0.309375, 0.334062, 0.400625, 0.420312, 0.527187, 0.589375, 0.656562, 0.729375
|
||||
#*# 0.139687, 0.074375, 0.025000, -0.008750, -0.019688, -0.025625, -0.045000, -0.023125, -0.037813, -0.043438, -0.047188, -0.008125, 0.020312, 0.022500, 0.049687, 0.096875, 0.154687, 0.209062, 0.195000, 0.269687, 0.285312, 0.335937, 0.373750, 0.455625, 0.492812, 0.588125, 0.647812, 0.730625
|
||||
#*# 0.077500, 0.035312, -0.002500, 0.005937, -0.022500, -0.063125, -0.059375, -0.042188, -0.084063, -0.081563, -0.068438, -0.050625, 0.015000, 0.004687, 0.052812, 0.108125, 0.137500, 0.181875, 0.214375, 0.249375, 0.330625, 0.364375, 0.420312, 0.445937, 0.525000, 0.594062, 0.658750, 0.728750
|
||||
#*# 0.079687, 0.062187, 0.061250, 0.014375, 0.009687, -0.008438, 0.005312, -0.004688, -0.039688, 0.017812, 0.015937, 0.045000, 0.043437, 0.075937, 0.130937, 0.170312, 0.182812, 0.259375, 0.273437, 0.355312, 0.408125, 0.454375, 0.524062, 0.538750, 0.618750, 0.659687, 0.748750, 0.808437
|
||||
#*# 0.118750, 0.060312, 0.075000, 0.078125, 0.068125, 0.055625, 0.030000, 0.062187, 0.052812, 0.047812, 0.091875, 0.095000, 0.144687, 0.176562, 0.152187, 0.186875, 0.243750, 0.301875, 0.344062, 0.390625, 0.464375, 0.500625, 0.560000, 0.599375, 0.638750, 0.738750, 0.757812, 0.857187
|
||||
#*# 0.200000, 0.159375, 0.148125, 0.158437, 0.150625, 0.133437, 0.129687, 0.117187, 0.136250, 0.187500, 0.180937, 0.180312, 0.215937, 0.228125, 0.293750, 0.345625, 0.357500, 0.383437, 0.454062, 0.500312, 0.550625, 0.620312, 0.626875, 0.693125, 0.728750, 0.790625, 0.868750, 0.950000
|
||||
#*# 0.300000, 0.284687, 0.257500, 0.252187, 0.267812, 0.217500, 0.220000, 0.236250, 0.229375, 0.292812, 0.321562, 0.341875, 0.365625, 0.384062, 0.377187, 0.444375, 0.526875, 0.519375, 0.576562, 0.601562, 0.627187, 0.690937, 0.734375, 0.811250, 0.818750, 0.892187, 0.951875, 1.015312
|
||||
#*# 0.389062, 0.406250, 0.380000, 0.379062, 0.353750, 0.365312, 0.364062, 0.405000, 0.419375, 0.409687, 0.435625, 0.489687, 0.496562, 0.524062, 0.565937, 0.570000, 0.558750, 0.638125, 0.688125, 0.730000, 0.759062, 0.819062, 0.875625, 0.909062, 0.982187, 1.008437, 1.092187, 1.169062
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 13
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 28
|
||||
#*# max_y = 459.96
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.82
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 19.661
|
||||
#*# pid_ki = 0.819
|
||||
#*# pid_kd = 117.969
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.455
|
||||
#*# pid_ki = 1.659
|
||||
#*# pid_kd = 626.020
|
||||
|
|
@ -1,304 +0,0 @@
|
|||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
[printer]
|
||||
max_velocity: 150
|
||||
max_accel: 500
|
||||
max_accel_to_decel: 500
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 20
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "false"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 100
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
#control: pid
|
||||
#pid_kp: 28.413
|
||||
#pid_ki: 1.334
|
||||
#pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 15,15
|
||||
mesh_max:465,460
|
||||
probe_count: 28,13
|
||||
fade_start: 1.0
|
||||
fade_end: 100.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.920
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.756250, 0.660312, 0.556562, 0.486875, 0.458750, 0.339687, 0.305312, 0.262812, 0.213750, 0.233125, 0.214062, 0.187812, 0.229375, 0.226250, 0.215937, 0.249062, 0.259062, 0.268750, 0.301875, 0.340000, 0.352500, 0.398125, 0.432187, 0.481875, 0.502500, 0.583437, 0.605000, 0.698750
|
||||
#*# 0.730937, 0.616250, 0.543125, 0.496562, 0.411250, 0.362500, 0.328750, 0.267500, 0.262500, 0.236562, 0.249062, 0.217500, 0.228125, 0.258437, 0.232812, 0.250000, 0.260000, 0.271562, 0.303750, 0.357812, 0.405312, 0.416562, 0.488437, 0.510000, 0.591250, 0.575312, 0.683125, 0.716250
|
||||
#*# 0.675312, 0.593750, 0.485312, 0.391562, 0.372187, 0.332187, 0.281250, 0.265937, 0.227500, 0.228437, 0.213437, 0.180937, 0.200312, 0.183437, 0.241875, 0.229062, 0.214687, 0.281875, 0.334375, 0.361875, 0.370312, 0.407187, 0.464687, 0.500000, 0.557187, 0.632812, 0.672500, 0.715625
|
||||
#*# 0.541250, 0.448437, 0.387812, 0.338125, 0.272812, 0.219062, 0.204687, 0.183750, 0.164375, 0.161250, 0.162812, 0.155000, 0.133750, 0.154062, 0.165000, 0.166875, 0.199375, 0.257187, 0.269062, 0.319375, 0.350937, 0.373125, 0.405937, 0.498437, 0.485937, 0.586250, 0.640937, 0.709062
|
||||
#*# 0.374062, 0.293750, 0.260000, 0.242187, 0.165625, 0.113750, 0.095625, 0.136562, 0.094062, 0.070937, 0.098125, 0.130000, 0.094687, 0.102500, 0.152187, 0.154375, 0.171875, 0.224687, 0.247812, 0.283437, 0.328750, 0.389062, 0.417812, 0.450000, 0.512187, 0.578125, 0.649062, 0.735625
|
||||
#*# 0.285937, 0.226562, 0.164062, 0.139687, 0.122500, 0.067500, 0.040937, 0.043437, 0.014375, 0.049375, 0.046250, 0.056562, 0.101875, 0.102812, 0.135000, 0.143437, 0.163750, 0.174375, 0.269687, 0.289375, 0.331875, 0.363750, 0.404687, 0.439687, 0.545312, 0.608750, 0.668437, 0.730000
|
||||
#*# 0.164062, 0.116562, 0.064687, 0.031875, 0.010937, 0.009062, -0.004063, 0.003125, -0.003750, -0.010000, -0.018438, 0.016562, 0.050625, 0.043125, 0.053750, 0.104687, 0.170625, 0.218750, 0.205625, 0.278750, 0.312500, 0.356875, 0.381250, 0.481875, 0.495937, 0.598437, 0.659687, 0.731875
|
||||
#*# 0.121250, 0.075000, 0.035312, 0.036562, 0.010000, -0.047813, -0.054375, -0.018438, -0.036250, -0.059063, -0.036875, -0.025313, 0.041875, 0.020937, 0.084687, 0.122187, 0.172500, 0.212812, 0.250000, 0.259375, 0.352812, 0.389062, 0.447500, 0.460000, 0.544062, 0.604062, 0.680937, 0.754687
|
||||
#*# 0.096875, 0.081562, 0.058125, 0.028125, 0.026562, 0.014062, 0.025937, 0.028437, -0.018125, 0.038437, 0.034062, 0.045625, 0.058125, 0.063125, 0.132187, 0.171875, 0.181562, 0.254375, 0.272187, 0.356250, 0.410625, 0.458750, 0.529062, 0.535625, 0.620625, 0.650937, 0.734062, 0.801562
|
||||
#*# 0.130625, 0.071250, 0.089687, 0.085312, 0.083437, 0.066562, 0.052812, 0.069062, 0.048750, 0.055937, 0.085625, 0.112187, 0.158125, 0.172500, 0.171562, 0.205000, 0.247812, 0.331250, 0.340625, 0.402812, 0.462812, 0.489062, 0.571875, 0.600625, 0.614687, 0.749375, 0.796562, 0.855937
|
||||
#*# 0.211562, 0.181875, 0.151875, 0.172812, 0.160000, 0.133125, 0.135937, 0.131875, 0.144687, 0.207812, 0.185625, 0.193437, 0.200312, 0.231562, 0.290312, 0.339375, 0.354375, 0.373437, 0.444375, 0.487500, 0.526875, 0.605625, 0.590937, 0.669062, 0.720937, 0.746875, 0.827812, 0.924687
|
||||
#*# 0.300937, 0.287500, 0.252812, 0.267187, 0.268125, 0.220625, 0.208125, 0.221875, 0.219375, 0.285312, 0.312187, 0.337187, 0.362812, 0.381562, 0.364062, 0.426250, 0.520937, 0.497187, 0.575000, 0.593750, 0.613125, 0.667187, 0.716250, 0.791875, 0.794375, 0.851875, 0.921875, 0.991250
|
||||
#*# 0.387187, 0.382500, 0.381562, 0.374687, 0.343437, 0.340625, 0.323750, 0.356875, 0.373125, 0.404375, 0.428437, 0.509062, 0.490312, 0.510625, 0.535937, 0.550312, 0.529687, 0.618437, 0.673437, 0.702500, 0.695000, 0.793125, 0.801875, 0.872812, 0.930312, 0.981250, 1.057812, 1.102187
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 13
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 28
|
||||
#*# max_y = 459.96
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.82
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 19.661
|
||||
#*# pid_ki = 0.819
|
||||
#*# pid_kd = 117.969
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.455
|
||||
#*# pid_ki = 1.659
|
||||
#*# pid_kd = 626.020
|
||||
|
|
@ -1,304 +0,0 @@
|
|||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
[printer]
|
||||
max_velocity: 150
|
||||
max_accel: 500
|
||||
max_accel_to_decel: 500
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 20
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "false"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 100
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
#control: pid
|
||||
#pid_kp: 28.413
|
||||
#pid_ki: 1.334
|
||||
#pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 15,15
|
||||
mesh_max:465,460
|
||||
probe_count: 28,13
|
||||
fade_start: 1.0
|
||||
fade_end: 100.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.940
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.756250, 0.660312, 0.556562, 0.486875, 0.458750, 0.339687, 0.305312, 0.262812, 0.213750, 0.233125, 0.214062, 0.187812, 0.229375, 0.226250, 0.215937, 0.249062, 0.259062, 0.268750, 0.301875, 0.340000, 0.352500, 0.398125, 0.432187, 0.481875, 0.502500, 0.583437, 0.605000, 0.698750
|
||||
#*# 0.730937, 0.616250, 0.543125, 0.496562, 0.411250, 0.362500, 0.328750, 0.267500, 0.262500, 0.236562, 0.249062, 0.217500, 0.228125, 0.258437, 0.232812, 0.250000, 0.260000, 0.271562, 0.303750, 0.357812, 0.405312, 0.416562, 0.488437, 0.510000, 0.591250, 0.575312, 0.683125, 0.716250
|
||||
#*# 0.675312, 0.593750, 0.485312, 0.391562, 0.372187, 0.332187, 0.281250, 0.265937, 0.227500, 0.228437, 0.213437, 0.180937, 0.200312, 0.183437, 0.241875, 0.229062, 0.214687, 0.281875, 0.334375, 0.361875, 0.370312, 0.407187, 0.464687, 0.500000, 0.557187, 0.632812, 0.672500, 0.715625
|
||||
#*# 0.541250, 0.448437, 0.387812, 0.338125, 0.272812, 0.219062, 0.204687, 0.183750, 0.164375, 0.161250, 0.162812, 0.155000, 0.133750, 0.154062, 0.165000, 0.166875, 0.199375, 0.257187, 0.269062, 0.319375, 0.350937, 0.373125, 0.405937, 0.498437, 0.485937, 0.586250, 0.640937, 0.709062
|
||||
#*# 0.374062, 0.293750, 0.260000, 0.242187, 0.165625, 0.113750, 0.095625, 0.136562, 0.094062, 0.070937, 0.098125, 0.130000, 0.094687, 0.102500, 0.152187, 0.154375, 0.171875, 0.224687, 0.247812, 0.283437, 0.328750, 0.389062, 0.417812, 0.450000, 0.512187, 0.578125, 0.649062, 0.735625
|
||||
#*# 0.285937, 0.226562, 0.164062, 0.139687, 0.122500, 0.067500, 0.040937, 0.043437, 0.014375, 0.049375, 0.046250, 0.056562, 0.101875, 0.102812, 0.135000, 0.143437, 0.163750, 0.174375, 0.269687, 0.289375, 0.331875, 0.363750, 0.404687, 0.439687, 0.545312, 0.608750, 0.668437, 0.730000
|
||||
#*# 0.164062, 0.116562, 0.064687, 0.031875, 0.010937, 0.009062, -0.004063, 0.003125, -0.003750, -0.010000, -0.018438, 0.016562, 0.050625, 0.043125, 0.053750, 0.104687, 0.170625, 0.218750, 0.205625, 0.278750, 0.312500, 0.356875, 0.381250, 0.481875, 0.495937, 0.598437, 0.659687, 0.731875
|
||||
#*# 0.121250, 0.075000, 0.035312, 0.036562, 0.010000, -0.047813, -0.054375, -0.018438, -0.036250, -0.059063, -0.036875, -0.025313, 0.041875, 0.020937, 0.084687, 0.122187, 0.172500, 0.212812, 0.250000, 0.259375, 0.352812, 0.389062, 0.447500, 0.460000, 0.544062, 0.604062, 0.680937, 0.754687
|
||||
#*# 0.096875, 0.081562, 0.058125, 0.028125, 0.026562, 0.014062, 0.025937, 0.028437, -0.018125, 0.038437, 0.034062, 0.045625, 0.058125, 0.063125, 0.132187, 0.171875, 0.181562, 0.254375, 0.272187, 0.356250, 0.410625, 0.458750, 0.529062, 0.535625, 0.620625, 0.650937, 0.734062, 0.801562
|
||||
#*# 0.130625, 0.071250, 0.089687, 0.085312, 0.083437, 0.066562, 0.052812, 0.069062, 0.048750, 0.055937, 0.085625, 0.112187, 0.158125, 0.172500, 0.171562, 0.205000, 0.247812, 0.331250, 0.340625, 0.402812, 0.462812, 0.489062, 0.571875, 0.600625, 0.614687, 0.749375, 0.796562, 0.855937
|
||||
#*# 0.211562, 0.181875, 0.151875, 0.172812, 0.160000, 0.133125, 0.135937, 0.131875, 0.144687, 0.207812, 0.185625, 0.193437, 0.200312, 0.231562, 0.290312, 0.339375, 0.354375, 0.373437, 0.444375, 0.487500, 0.526875, 0.605625, 0.590937, 0.669062, 0.720937, 0.746875, 0.827812, 0.924687
|
||||
#*# 0.300937, 0.287500, 0.252812, 0.267187, 0.268125, 0.220625, 0.208125, 0.221875, 0.219375, 0.285312, 0.312187, 0.337187, 0.362812, 0.381562, 0.364062, 0.426250, 0.520937, 0.497187, 0.575000, 0.593750, 0.613125, 0.667187, 0.716250, 0.791875, 0.794375, 0.851875, 0.921875, 0.991250
|
||||
#*# 0.387187, 0.382500, 0.381562, 0.374687, 0.343437, 0.340625, 0.323750, 0.356875, 0.373125, 0.404375, 0.428437, 0.509062, 0.490312, 0.510625, 0.535937, 0.550312, 0.529687, 0.618437, 0.673437, 0.702500, 0.695000, 0.793125, 0.801875, 0.872812, 0.930312, 0.981250, 1.057812, 1.102187
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 13
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 28
|
||||
#*# max_y = 459.96
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.82
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 19.661
|
||||
#*# pid_ki = 0.819
|
||||
#*# pid_kd = 117.969
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.455
|
||||
#*# pid_ki = 1.659
|
||||
#*# pid_kd = 626.020
|
||||
|
|
@ -1,304 +0,0 @@
|
|||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
[printer]
|
||||
max_velocity: 150
|
||||
max_accel: 500
|
||||
max_accel_to_decel: 500
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 20
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "false"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 100
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
#control: pid
|
||||
#pid_kp: 28.413
|
||||
#pid_ki: 1.334
|
||||
#pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 15,15
|
||||
mesh_max:465,460
|
||||
probe_count: 28,13
|
||||
fade_start: 1.0
|
||||
fade_end: 100.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.910
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.756250, 0.660312, 0.556562, 0.486875, 0.458750, 0.339687, 0.305312, 0.262812, 0.213750, 0.233125, 0.214062, 0.187812, 0.229375, 0.226250, 0.215937, 0.249062, 0.259062, 0.268750, 0.301875, 0.340000, 0.352500, 0.398125, 0.432187, 0.481875, 0.502500, 0.583437, 0.605000, 0.698750
|
||||
#*# 0.730937, 0.616250, 0.543125, 0.496562, 0.411250, 0.362500, 0.328750, 0.267500, 0.262500, 0.236562, 0.249062, 0.217500, 0.228125, 0.258437, 0.232812, 0.250000, 0.260000, 0.271562, 0.303750, 0.357812, 0.405312, 0.416562, 0.488437, 0.510000, 0.591250, 0.575312, 0.683125, 0.716250
|
||||
#*# 0.675312, 0.593750, 0.485312, 0.391562, 0.372187, 0.332187, 0.281250, 0.265937, 0.227500, 0.228437, 0.213437, 0.180937, 0.200312, 0.183437, 0.241875, 0.229062, 0.214687, 0.281875, 0.334375, 0.361875, 0.370312, 0.407187, 0.464687, 0.500000, 0.557187, 0.632812, 0.672500, 0.715625
|
||||
#*# 0.541250, 0.448437, 0.387812, 0.338125, 0.272812, 0.219062, 0.204687, 0.183750, 0.164375, 0.161250, 0.162812, 0.155000, 0.133750, 0.154062, 0.165000, 0.166875, 0.199375, 0.257187, 0.269062, 0.319375, 0.350937, 0.373125, 0.405937, 0.498437, 0.485937, 0.586250, 0.640937, 0.709062
|
||||
#*# 0.374062, 0.293750, 0.260000, 0.242187, 0.165625, 0.113750, 0.095625, 0.136562, 0.094062, 0.070937, 0.098125, 0.130000, 0.094687, 0.102500, 0.152187, 0.154375, 0.171875, 0.224687, 0.247812, 0.283437, 0.328750, 0.389062, 0.417812, 0.450000, 0.512187, 0.578125, 0.649062, 0.735625
|
||||
#*# 0.285937, 0.226562, 0.164062, 0.139687, 0.122500, 0.067500, 0.040937, 0.043437, 0.014375, 0.049375, 0.046250, 0.056562, 0.101875, 0.102812, 0.135000, 0.143437, 0.163750, 0.174375, 0.269687, 0.289375, 0.331875, 0.363750, 0.404687, 0.439687, 0.545312, 0.608750, 0.668437, 0.730000
|
||||
#*# 0.164062, 0.116562, 0.064687, 0.031875, 0.010937, 0.009062, -0.004063, 0.003125, -0.003750, -0.010000, -0.018438, 0.016562, 0.050625, 0.043125, 0.053750, 0.104687, 0.170625, 0.218750, 0.205625, 0.278750, 0.312500, 0.356875, 0.381250, 0.481875, 0.495937, 0.598437, 0.659687, 0.731875
|
||||
#*# 0.121250, 0.075000, 0.035312, 0.036562, 0.010000, -0.047813, -0.054375, -0.018438, -0.036250, -0.059063, -0.036875, -0.025313, 0.041875, 0.020937, 0.084687, 0.122187, 0.172500, 0.212812, 0.250000, 0.259375, 0.352812, 0.389062, 0.447500, 0.460000, 0.544062, 0.604062, 0.680937, 0.754687
|
||||
#*# 0.096875, 0.081562, 0.058125, 0.028125, 0.026562, 0.014062, 0.025937, 0.028437, -0.018125, 0.038437, 0.034062, 0.045625, 0.058125, 0.063125, 0.132187, 0.171875, 0.181562, 0.254375, 0.272187, 0.356250, 0.410625, 0.458750, 0.529062, 0.535625, 0.620625, 0.650937, 0.734062, 0.801562
|
||||
#*# 0.130625, 0.071250, 0.089687, 0.085312, 0.083437, 0.066562, 0.052812, 0.069062, 0.048750, 0.055937, 0.085625, 0.112187, 0.158125, 0.172500, 0.171562, 0.205000, 0.247812, 0.331250, 0.340625, 0.402812, 0.462812, 0.489062, 0.571875, 0.600625, 0.614687, 0.749375, 0.796562, 0.855937
|
||||
#*# 0.211562, 0.181875, 0.151875, 0.172812, 0.160000, 0.133125, 0.135937, 0.131875, 0.144687, 0.207812, 0.185625, 0.193437, 0.200312, 0.231562, 0.290312, 0.339375, 0.354375, 0.373437, 0.444375, 0.487500, 0.526875, 0.605625, 0.590937, 0.669062, 0.720937, 0.746875, 0.827812, 0.924687
|
||||
#*# 0.300937, 0.287500, 0.252812, 0.267187, 0.268125, 0.220625, 0.208125, 0.221875, 0.219375, 0.285312, 0.312187, 0.337187, 0.362812, 0.381562, 0.364062, 0.426250, 0.520937, 0.497187, 0.575000, 0.593750, 0.613125, 0.667187, 0.716250, 0.791875, 0.794375, 0.851875, 0.921875, 0.991250
|
||||
#*# 0.387187, 0.382500, 0.381562, 0.374687, 0.343437, 0.340625, 0.323750, 0.356875, 0.373125, 0.404375, 0.428437, 0.509062, 0.490312, 0.510625, 0.535937, 0.550312, 0.529687, 0.618437, 0.673437, 0.702500, 0.695000, 0.793125, 0.801875, 0.872812, 0.930312, 0.981250, 1.057812, 1.102187
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 13
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 28
|
||||
#*# max_y = 459.96
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.82
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 19.661
|
||||
#*# pid_ki = 0.819
|
||||
#*# pid_kd = 117.969
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.455
|
||||
#*# pid_ki = 1.659
|
||||
#*# pid_kd = 626.020
|
||||
|
|
@ -1,304 +0,0 @@
|
|||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
[printer]
|
||||
max_velocity: 150
|
||||
max_accel: 500
|
||||
max_accel_to_decel: 500
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 20
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "false"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 100
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
#control: pid
|
||||
#pid_kp: 28.413
|
||||
#pid_ki: 1.334
|
||||
#pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 15,15
|
||||
mesh_max:465,460
|
||||
probe_count: 28,13
|
||||
fade_start: 1.0
|
||||
fade_end: 100.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.910
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.660625, 0.566875, 0.463437, 0.423125, 0.387187, 0.296875, 0.255000, 0.200625, 0.168437, 0.174375, 0.146562, 0.173750, 0.198125, 0.191250, 0.175312, 0.209062, 0.230000, 0.242500, 0.277812, 0.328437, 0.338125, 0.369687, 0.399687, 0.445937, 0.447187, 0.527500, 0.563125, 0.671562
|
||||
#*# 0.589375, 0.495625, 0.426562, 0.377500, 0.317812, 0.265312, 0.246562, 0.200625, 0.195312, 0.166250, 0.143437, 0.165625, 0.164687, 0.213437, 0.200000, 0.205312, 0.208750, 0.248750, 0.286562, 0.316875, 0.360000, 0.375625, 0.439062, 0.472187, 0.520312, 0.527812, 0.629062, 0.649062
|
||||
#*# 0.529375, 0.480312, 0.355937, 0.295937, 0.245312, 0.220937, 0.187187, 0.184062, 0.146562, 0.159687, 0.155312, 0.121250, 0.144062, 0.134062, 0.165937, 0.159062, 0.172812, 0.207500, 0.284375, 0.320625, 0.320312, 0.362500, 0.415625, 0.443437, 0.510937, 0.565312, 0.589687, 0.658125
|
||||
#*# 0.395625, 0.303437, 0.240937, 0.227812, 0.188750, 0.147500, 0.117187, 0.090000, 0.083437, 0.090937, 0.098437, 0.098437, 0.089687, 0.110625, 0.116562, 0.120937, 0.155937, 0.212187, 0.207187, 0.265625, 0.299375, 0.328125, 0.365937, 0.438750, 0.431250, 0.522812, 0.553437, 0.644375
|
||||
#*# 0.199062, 0.169062, 0.135312, 0.133437, 0.056250, 0.018125, 0.000625, 0.025937, 0.020937, 0.011875, 0.010312, 0.070312, 0.052500, 0.045000, 0.090000, 0.076875, 0.122187, 0.181562, 0.196562, 0.224062, 0.287812, 0.316250, 0.373437, 0.400000, 0.446562, 0.500937, 0.570937, 0.632812
|
||||
#*# 0.144687, 0.100625, 0.042187, 0.018125, -0.004063, -0.036250, -0.051563, -0.043125, -0.056250, -0.003750, 0.004062, 0.022812, 0.045312, 0.060625, 0.088750, 0.114687, 0.107812, 0.122500, 0.225000, 0.247187, 0.277812, 0.321250, 0.345625, 0.380000, 0.472812, 0.530625, 0.586875, 0.660312
|
||||
#*# 0.020000, -0.008750, -0.035938, -0.069688, -0.062500, -0.074688, -0.118438, -0.076563, -0.077500, -0.070313, -0.069688, -0.030313, -0.004688, 0.010312, 0.011562, 0.075625, 0.142187, 0.182187, 0.162187, 0.246875, 0.266562, 0.310937, 0.334375, 0.418437, 0.440937, 0.532187, 0.583437, 0.649375
|
||||
#*# 0.029687, -0.000000, -0.145938, -0.070938, -0.092500, -0.116250, -0.115938, -0.081563, -0.107813, -0.093750, -0.078438, -0.061563, -0.003125, -0.027500, 0.051875, 0.079062, 0.134687, 0.165937, 0.198750, 0.221875, 0.304687, 0.339375, 0.386250, 0.395000, 0.481562, 0.536250, 0.591562, 0.664687
|
||||
#*# 0.006562, -0.030000, -0.033750, -0.034063, -0.035625, -0.040313, -0.036875, -0.004688, -0.050938, 0.006250, 0.012500, 0.018750, 0.047812, 0.044687, 0.123750, 0.169062, 0.189375, 0.264062, 0.274062, 0.338750, 0.386562, 0.445000, 0.503125, 0.504062, 0.586562, 0.621250, 0.700312, 0.748125
|
||||
#*# 0.038125, -0.001250, 0.011562, 0.004062, 0.004687, 0.011562, 0.006250, 0.028437, 0.035937, 0.030312, 0.061250, 0.079062, 0.123437, 0.156250, 0.153125, 0.183750, 0.239687, 0.309375, 0.336562, 0.370625, 0.439062, 0.461875, 0.536562, 0.563125, 0.581562, 0.696250, 0.715625, 0.794375
|
||||
#*# 0.108125, 0.103437, 0.082812, 0.090625, 0.092500, 0.089062, 0.085000, 0.097187, 0.113437, 0.154687, 0.159375, 0.167187, 0.184687, 0.216562, 0.275312, 0.329375, 0.332187, 0.370937, 0.439062, 0.478125, 0.517812, 0.579687, 0.587500, 0.647812, 0.680625, 0.709375, 0.795937, 0.858437
|
||||
#*# 0.200937, 0.185937, 0.171562, 0.184062, 0.204062, 0.170000, 0.162187, 0.178125, 0.195937, 0.260000, 0.287812, 0.309687, 0.350937, 0.372187, 0.353437, 0.415625, 0.490937, 0.477500, 0.553750, 0.578125, 0.601250, 0.647812, 0.686562, 0.759062, 0.754687, 0.810937, 0.881250, 0.938125
|
||||
#*# 0.297812, 0.298750, 0.298437, 0.292812, 0.282812, 0.271562, 0.273750, 0.310937, 0.329687, 0.354062, 0.395312, 0.482187, 0.468750, 0.471562, 0.514062, 0.533125, 0.514375, 0.603750, 0.649375, 0.678750, 0.677812, 0.757500, 0.769062, 0.842812, 0.905937, 0.929375, 1.005937, 1.078125
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 13
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 28
|
||||
#*# max_y = 459.96
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.82
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 19.661
|
||||
#*# pid_ki = 0.819
|
||||
#*# pid_kd = 117.969
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.455
|
||||
#*# pid_ki = 1.659
|
||||
#*# pid_kd = 626.020
|
||||
|
|
@ -1,304 +0,0 @@
|
|||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
[printer]
|
||||
max_velocity: 150
|
||||
max_accel: 500
|
||||
max_accel_to_decel: 500
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 20
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "false"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 100
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
#control: pid
|
||||
#pid_kp: 28.413
|
||||
#pid_ki: 1.334
|
||||
#pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 15,15
|
||||
mesh_max:465,460
|
||||
probe_count: 28,13
|
||||
fade_start: 1.0
|
||||
fade_end: 100.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.950
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.660625, 0.566875, 0.463437, 0.423125, 0.387187, 0.296875, 0.255000, 0.200625, 0.168437, 0.174375, 0.146562, 0.173750, 0.198125, 0.191250, 0.175312, 0.209062, 0.230000, 0.242500, 0.277812, 0.328437, 0.338125, 0.369687, 0.399687, 0.445937, 0.447187, 0.527500, 0.563125, 0.671562
|
||||
#*# 0.589375, 0.495625, 0.426562, 0.377500, 0.317812, 0.265312, 0.246562, 0.200625, 0.195312, 0.166250, 0.143437, 0.165625, 0.164687, 0.213437, 0.200000, 0.205312, 0.208750, 0.248750, 0.286562, 0.316875, 0.360000, 0.375625, 0.439062, 0.472187, 0.520312, 0.527812, 0.629062, 0.649062
|
||||
#*# 0.529375, 0.480312, 0.355937, 0.295937, 0.245312, 0.220937, 0.187187, 0.184062, 0.146562, 0.159687, 0.155312, 0.121250, 0.144062, 0.134062, 0.165937, 0.159062, 0.172812, 0.207500, 0.284375, 0.320625, 0.320312, 0.362500, 0.415625, 0.443437, 0.510937, 0.565312, 0.589687, 0.658125
|
||||
#*# 0.395625, 0.303437, 0.240937, 0.227812, 0.188750, 0.147500, 0.117187, 0.090000, 0.083437, 0.090937, 0.098437, 0.098437, 0.089687, 0.110625, 0.116562, 0.120937, 0.155937, 0.212187, 0.207187, 0.265625, 0.299375, 0.328125, 0.365937, 0.438750, 0.431250, 0.522812, 0.553437, 0.644375
|
||||
#*# 0.199062, 0.169062, 0.135312, 0.133437, 0.056250, 0.018125, 0.000625, 0.025937, 0.020937, 0.011875, 0.010312, 0.070312, 0.052500, 0.045000, 0.090000, 0.076875, 0.122187, 0.181562, 0.196562, 0.224062, 0.287812, 0.316250, 0.373437, 0.400000, 0.446562, 0.500937, 0.570937, 0.632812
|
||||
#*# 0.144687, 0.100625, 0.042187, 0.018125, -0.004063, -0.036250, -0.051563, -0.043125, -0.056250, -0.003750, 0.004062, 0.022812, 0.045312, 0.060625, 0.088750, 0.114687, 0.107812, 0.122500, 0.225000, 0.247187, 0.277812, 0.321250, 0.345625, 0.380000, 0.472812, 0.530625, 0.586875, 0.660312
|
||||
#*# 0.020000, -0.008750, -0.035938, -0.069688, -0.062500, -0.074688, -0.118438, -0.076563, -0.077500, -0.070313, -0.069688, -0.030313, -0.004688, 0.010312, 0.011562, 0.075625, 0.142187, 0.182187, 0.162187, 0.246875, 0.266562, 0.310937, 0.334375, 0.418437, 0.440937, 0.532187, 0.583437, 0.649375
|
||||
#*# 0.029687, -0.000000, -0.145938, -0.070938, -0.092500, -0.116250, -0.115938, -0.081563, -0.107813, -0.093750, -0.078438, -0.061563, -0.003125, -0.027500, 0.051875, 0.079062, 0.134687, 0.165937, 0.198750, 0.221875, 0.304687, 0.339375, 0.386250, 0.395000, 0.481562, 0.536250, 0.591562, 0.664687
|
||||
#*# 0.006562, -0.030000, -0.033750, -0.034063, -0.035625, -0.040313, -0.036875, -0.004688, -0.050938, 0.006250, 0.012500, 0.018750, 0.047812, 0.044687, 0.123750, 0.169062, 0.189375, 0.264062, 0.274062, 0.338750, 0.386562, 0.445000, 0.503125, 0.504062, 0.586562, 0.621250, 0.700312, 0.748125
|
||||
#*# 0.038125, -0.001250, 0.011562, 0.004062, 0.004687, 0.011562, 0.006250, 0.028437, 0.035937, 0.030312, 0.061250, 0.079062, 0.123437, 0.156250, 0.153125, 0.183750, 0.239687, 0.309375, 0.336562, 0.370625, 0.439062, 0.461875, 0.536562, 0.563125, 0.581562, 0.696250, 0.715625, 0.794375
|
||||
#*# 0.108125, 0.103437, 0.082812, 0.090625, 0.092500, 0.089062, 0.085000, 0.097187, 0.113437, 0.154687, 0.159375, 0.167187, 0.184687, 0.216562, 0.275312, 0.329375, 0.332187, 0.370937, 0.439062, 0.478125, 0.517812, 0.579687, 0.587500, 0.647812, 0.680625, 0.709375, 0.795937, 0.858437
|
||||
#*# 0.200937, 0.185937, 0.171562, 0.184062, 0.204062, 0.170000, 0.162187, 0.178125, 0.195937, 0.260000, 0.287812, 0.309687, 0.350937, 0.372187, 0.353437, 0.415625, 0.490937, 0.477500, 0.553750, 0.578125, 0.601250, 0.647812, 0.686562, 0.759062, 0.754687, 0.810937, 0.881250, 0.938125
|
||||
#*# 0.297812, 0.298750, 0.298437, 0.292812, 0.282812, 0.271562, 0.273750, 0.310937, 0.329687, 0.354062, 0.395312, 0.482187, 0.468750, 0.471562, 0.514062, 0.533125, 0.514375, 0.603750, 0.649375, 0.678750, 0.677812, 0.757500, 0.769062, 0.842812, 0.905937, 0.929375, 1.005937, 1.078125
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 13
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 28
|
||||
#*# max_y = 459.96
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.82
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 19.661
|
||||
#*# pid_ki = 0.819
|
||||
#*# pid_kd = 117.969
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.455
|
||||
#*# pid_ki = 1.659
|
||||
#*# pid_kd = 626.020
|
||||
|
|
@ -1,304 +0,0 @@
|
|||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
[printer]
|
||||
max_velocity: 150
|
||||
max_accel: 500
|
||||
max_accel_to_decel: 500
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 20
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "false"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 100
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
#control: pid
|
||||
#pid_kp: 28.413
|
||||
#pid_ki: 1.334
|
||||
#pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 15,15
|
||||
mesh_max:465,460
|
||||
probe_count: 28,13
|
||||
fade_start: 1.0
|
||||
fade_end: 100.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.960
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.660625, 0.566875, 0.463437, 0.423125, 0.387187, 0.296875, 0.255000, 0.200625, 0.168437, 0.174375, 0.146562, 0.173750, 0.198125, 0.191250, 0.175312, 0.209062, 0.230000, 0.242500, 0.277812, 0.328437, 0.338125, 0.369687, 0.399687, 0.445937, 0.447187, 0.527500, 0.563125, 0.671562
|
||||
#*# 0.589375, 0.495625, 0.426562, 0.377500, 0.317812, 0.265312, 0.246562, 0.200625, 0.195312, 0.166250, 0.143437, 0.165625, 0.164687, 0.213437, 0.200000, 0.205312, 0.208750, 0.248750, 0.286562, 0.316875, 0.360000, 0.375625, 0.439062, 0.472187, 0.520312, 0.527812, 0.629062, 0.649062
|
||||
#*# 0.529375, 0.480312, 0.355937, 0.295937, 0.245312, 0.220937, 0.187187, 0.184062, 0.146562, 0.159687, 0.155312, 0.121250, 0.144062, 0.134062, 0.165937, 0.159062, 0.172812, 0.207500, 0.284375, 0.320625, 0.320312, 0.362500, 0.415625, 0.443437, 0.510937, 0.565312, 0.589687, 0.658125
|
||||
#*# 0.395625, 0.303437, 0.240937, 0.227812, 0.188750, 0.147500, 0.117187, 0.090000, 0.083437, 0.090937, 0.098437, 0.098437, 0.089687, 0.110625, 0.116562, 0.120937, 0.155937, 0.212187, 0.207187, 0.265625, 0.299375, 0.328125, 0.365937, 0.438750, 0.431250, 0.522812, 0.553437, 0.644375
|
||||
#*# 0.199062, 0.169062, 0.135312, 0.133437, 0.056250, 0.018125, 0.000625, 0.025937, 0.020937, 0.011875, 0.010312, 0.070312, 0.052500, 0.045000, 0.090000, 0.076875, 0.122187, 0.181562, 0.196562, 0.224062, 0.287812, 0.316250, 0.373437, 0.400000, 0.446562, 0.500937, 0.570937, 0.632812
|
||||
#*# 0.144687, 0.100625, 0.042187, 0.018125, -0.004063, -0.036250, -0.051563, -0.043125, -0.056250, -0.003750, 0.004062, 0.022812, 0.045312, 0.060625, 0.088750, 0.114687, 0.107812, 0.122500, 0.225000, 0.247187, 0.277812, 0.321250, 0.345625, 0.380000, 0.472812, 0.530625, 0.586875, 0.660312
|
||||
#*# 0.020000, -0.008750, -0.035938, -0.069688, -0.062500, -0.074688, -0.118438, -0.076563, -0.077500, -0.070313, -0.069688, -0.030313, -0.004688, 0.010312, 0.011562, 0.075625, 0.142187, 0.182187, 0.162187, 0.246875, 0.266562, 0.310937, 0.334375, 0.418437, 0.440937, 0.532187, 0.583437, 0.649375
|
||||
#*# 0.029687, -0.000000, -0.145938, -0.070938, -0.092500, -0.116250, -0.115938, -0.081563, -0.107813, -0.093750, -0.078438, -0.061563, -0.003125, -0.027500, 0.051875, 0.079062, 0.134687, 0.165937, 0.198750, 0.221875, 0.304687, 0.339375, 0.386250, 0.395000, 0.481562, 0.536250, 0.591562, 0.664687
|
||||
#*# 0.006562, -0.030000, -0.033750, -0.034063, -0.035625, -0.040313, -0.036875, -0.004688, -0.050938, 0.006250, 0.012500, 0.018750, 0.047812, 0.044687, 0.123750, 0.169062, 0.189375, 0.264062, 0.274062, 0.338750, 0.386562, 0.445000, 0.503125, 0.504062, 0.586562, 0.621250, 0.700312, 0.748125
|
||||
#*# 0.038125, -0.001250, 0.011562, 0.004062, 0.004687, 0.011562, 0.006250, 0.028437, 0.035937, 0.030312, 0.061250, 0.079062, 0.123437, 0.156250, 0.153125, 0.183750, 0.239687, 0.309375, 0.336562, 0.370625, 0.439062, 0.461875, 0.536562, 0.563125, 0.581562, 0.696250, 0.715625, 0.794375
|
||||
#*# 0.108125, 0.103437, 0.082812, 0.090625, 0.092500, 0.089062, 0.085000, 0.097187, 0.113437, 0.154687, 0.159375, 0.167187, 0.184687, 0.216562, 0.275312, 0.329375, 0.332187, 0.370937, 0.439062, 0.478125, 0.517812, 0.579687, 0.587500, 0.647812, 0.680625, 0.709375, 0.795937, 0.858437
|
||||
#*# 0.200937, 0.185937, 0.171562, 0.184062, 0.204062, 0.170000, 0.162187, 0.178125, 0.195937, 0.260000, 0.287812, 0.309687, 0.350937, 0.372187, 0.353437, 0.415625, 0.490937, 0.477500, 0.553750, 0.578125, 0.601250, 0.647812, 0.686562, 0.759062, 0.754687, 0.810937, 0.881250, 0.938125
|
||||
#*# 0.297812, 0.298750, 0.298437, 0.292812, 0.282812, 0.271562, 0.273750, 0.310937, 0.329687, 0.354062, 0.395312, 0.482187, 0.468750, 0.471562, 0.514062, 0.533125, 0.514375, 0.603750, 0.649375, 0.678750, 0.677812, 0.757500, 0.769062, 0.842812, 0.905937, 0.929375, 1.005937, 1.078125
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 13
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 28
|
||||
#*# max_y = 459.96
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.82
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 19.661
|
||||
#*# pid_ki = 0.819
|
||||
#*# pid_kd = 117.969
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.455
|
||||
#*# pid_ki = 1.659
|
||||
#*# pid_kd = 626.020
|
||||
|
|
@ -1,304 +0,0 @@
|
|||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
[printer]
|
||||
max_velocity: 150
|
||||
max_accel: 500
|
||||
max_accel_to_decel: 500
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 20
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "false"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 100
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
#control: pid
|
||||
#pid_kp: 28.413
|
||||
#pid_ki: 1.334
|
||||
#pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 15,15
|
||||
mesh_max:465,460
|
||||
probe_count: 28,13
|
||||
fade_start: 1.0
|
||||
fade_end: 100.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.960
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.631562, 0.519062, 0.440625, 0.370000, 0.328750, 0.264687, 0.178125, 0.155312, 0.154062, 0.143125, 0.092187, 0.082500, 0.077500, 0.120312, 0.130000, 0.145000, 0.164062, 0.166250, 0.192812, 0.240312, 0.287812, 0.311562, 0.365312, 0.344687, 0.417500, 0.520000, 0.499687, 0.646875
|
||||
#*# 0.592500, 0.534375, 0.431250, 0.362812, 0.309687, 0.258125, 0.219062, 0.156562, 0.180625, 0.134687, 0.139375, 0.126562, 0.179375, 0.160000, 0.158437, 0.134375, 0.169062, 0.195625, 0.236562, 0.260625, 0.316562, 0.332812, 0.376875, 0.440000, 0.450937, 0.506250, 0.573437, 0.659687
|
||||
#*# 0.538125, 0.494375, 0.371562, 0.335625, 0.252500, 0.220625, 0.207187, 0.190000, 0.153437, 0.129375, 0.152187, 0.122812, 0.135000, 0.119062, 0.160000, 0.153125, 0.193437, 0.204375, 0.244687, 0.315312, 0.333750, 0.359687, 0.393750, 0.444062, 0.485937, 0.544687, 0.587812, 0.647187
|
||||
#*# 0.433437, 0.361562, 0.297812, 0.259687, 0.191875, 0.139687, 0.137187, 0.103750, 0.086562, 0.053437, 0.084375, 0.082500, 0.081875, 0.098750, 0.079062, 0.121875, 0.150625, 0.201562, 0.217812, 0.249375, 0.303437, 0.322187, 0.369375, 0.419375, 0.486875, 0.538437, 0.592812, 0.661562
|
||||
#*# 0.259062, 0.211562, 0.134062, 0.146562, 0.102812, 0.079375, 0.042812, 0.029687, -0.025000, 0.016562, 0.047500, 0.062187, 0.041875, 0.050000, 0.078125, 0.108125, 0.146562, 0.169687, 0.210312, 0.268437, 0.297187, 0.337500, 0.365937, 0.449687, 0.476875, 0.553750, 0.596875, 0.675625
|
||||
#*# 0.173437, 0.137812, 0.099062, 0.059062, 0.065312, 0.011250, -0.010938, -0.042188, -0.032500, -0.007500, 0.011562, 0.030312, 0.035625, 0.053437, 0.076250, 0.115312, 0.112812, 0.147187, 0.196250, 0.232812, 0.296250, 0.341250, 0.375312, 0.427500, 0.493437, 0.558125, 0.643125, 0.678125
|
||||
#*# 0.064687, 0.053750, 0.030312, -0.045938, -0.017188, -0.067188, -0.078438, -0.093750, -0.119688, -0.067500, -0.067813, -0.069063, -0.025938, 0.006250, 0.038125, 0.090000, 0.076250, 0.145625, 0.177812, 0.239062, 0.296562, 0.330937, 0.386562, 0.412187, 0.471562, 0.538750, 0.625000, 0.701250
|
||||
#*# 0.038750, 0.005312, -0.043750, -0.070938, -0.087500, -0.061563, -0.100313, -0.099063, -0.081563, -0.073125, -0.070313, -0.038125, -0.006563, -0.009375, 0.021250, 0.057187, 0.083437, 0.161875, 0.189375, 0.238437, 0.285312, 0.346250, 0.384687, 0.427187, 0.532812, 0.580000, 0.667187, 0.739687
|
||||
#*# 0.035000, 0.000312, -0.009688, -0.063750, -0.027188, -0.044063, -0.045313, -0.067500, -0.014688, -0.045313, -0.015625, 0.004375, 0.017187, 0.038125, 0.069687, 0.104375, 0.177187, 0.199062, 0.236250, 0.325000, 0.330312, 0.398437, 0.446562, 0.523125, 0.562187, 0.621250, 0.686562, 0.782187
|
||||
#*# 0.047500, -0.008438, -0.017500, 0.002812, 0.025625, -0.002188, -0.050313, 0.017500, -0.025938, 0.021875, 0.027812, 0.022812, 0.071250, 0.103750, 0.145937, 0.174687, 0.198125, 0.264687, 0.277812, 0.383750, 0.398125, 0.462812, 0.482812, 0.558125, 0.605937, 0.645312, 0.728437, 0.781250
|
||||
#*# 0.129375, 0.089687, 0.057500, 0.059062, 0.052187, 0.056562, 0.062500, 0.054687, 0.095937, 0.090625, 0.134687, 0.134687, 0.176562, 0.196875, 0.223750, 0.305000, 0.295312, 0.349375, 0.398125, 0.429375, 0.495000, 0.539062, 0.579687, 0.630312, 0.691562, 0.709375, 0.798750, 0.873750
|
||||
#*# 0.200000, 0.209062, 0.191562, 0.141875, 0.185312, 0.148437, 0.186875, 0.150625, 0.192187, 0.193750, 0.232812, 0.256250, 0.286250, 0.311562, 0.362500, 0.392500, 0.420937, 0.434687, 0.519687, 0.542812, 0.584375, 0.596875, 0.697812, 0.702500, 0.776562, 0.834375, 0.890312, 0.994375
|
||||
#*# 0.283125, 0.290000, 0.252500, 0.257187, 0.282812, 0.249687, 0.296250, 0.315625, 0.312812, 0.328437, 0.360625, 0.424062, 0.406250, 0.454375, 0.492187, 0.525312, 0.544062, 0.614375, 0.626562, 0.675625, 0.685937, 0.756250, 0.810312, 0.850000, 0.889687, 0.947812, 1.011250, 1.059687
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 13
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 28
|
||||
#*# max_y = 459.96
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.82
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 19.661
|
||||
#*# pid_ki = 0.819
|
||||
#*# pid_kd = 117.969
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.455
|
||||
#*# pid_ki = 1.659
|
||||
#*# pid_kd = 626.020
|
||||
|
|
@ -1,304 +0,0 @@
|
|||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
[printer]
|
||||
max_velocity: 150
|
||||
max_accel: 500
|
||||
max_accel_to_decel: 500
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 20
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "false"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 100
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
#control: pid
|
||||
#pid_kp: 28.413
|
||||
#pid_ki: 1.334
|
||||
#pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 15,15
|
||||
mesh_max:465,460
|
||||
probe_count: 28,13
|
||||
fade_start: 1.0
|
||||
fade_end: 100.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 2.980
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.631562, 0.519062, 0.440625, 0.370000, 0.328750, 0.264687, 0.178125, 0.155312, 0.154062, 0.143125, 0.092187, 0.082500, 0.077500, 0.120312, 0.130000, 0.145000, 0.164062, 0.166250, 0.192812, 0.240312, 0.287812, 0.311562, 0.365312, 0.344687, 0.417500, 0.520000, 0.499687, 0.646875
|
||||
#*# 0.592500, 0.534375, 0.431250, 0.362812, 0.309687, 0.258125, 0.219062, 0.156562, 0.180625, 0.134687, 0.139375, 0.126562, 0.179375, 0.160000, 0.158437, 0.134375, 0.169062, 0.195625, 0.236562, 0.260625, 0.316562, 0.332812, 0.376875, 0.440000, 0.450937, 0.506250, 0.573437, 0.659687
|
||||
#*# 0.538125, 0.494375, 0.371562, 0.335625, 0.252500, 0.220625, 0.207187, 0.190000, 0.153437, 0.129375, 0.152187, 0.122812, 0.135000, 0.119062, 0.160000, 0.153125, 0.193437, 0.204375, 0.244687, 0.315312, 0.333750, 0.359687, 0.393750, 0.444062, 0.485937, 0.544687, 0.587812, 0.647187
|
||||
#*# 0.433437, 0.361562, 0.297812, 0.259687, 0.191875, 0.139687, 0.137187, 0.103750, 0.086562, 0.053437, 0.084375, 0.082500, 0.081875, 0.098750, 0.079062, 0.121875, 0.150625, 0.201562, 0.217812, 0.249375, 0.303437, 0.322187, 0.369375, 0.419375, 0.486875, 0.538437, 0.592812, 0.661562
|
||||
#*# 0.259062, 0.211562, 0.134062, 0.146562, 0.102812, 0.079375, 0.042812, 0.029687, -0.025000, 0.016562, 0.047500, 0.062187, 0.041875, 0.050000, 0.078125, 0.108125, 0.146562, 0.169687, 0.210312, 0.268437, 0.297187, 0.337500, 0.365937, 0.449687, 0.476875, 0.553750, 0.596875, 0.675625
|
||||
#*# 0.173437, 0.137812, 0.099062, 0.059062, 0.065312, 0.011250, -0.010938, -0.042188, -0.032500, -0.007500, 0.011562, 0.030312, 0.035625, 0.053437, 0.076250, 0.115312, 0.112812, 0.147187, 0.196250, 0.232812, 0.296250, 0.341250, 0.375312, 0.427500, 0.493437, 0.558125, 0.643125, 0.678125
|
||||
#*# 0.064687, 0.053750, 0.030312, -0.045938, -0.017188, -0.067188, -0.078438, -0.093750, -0.119688, -0.067500, -0.067813, -0.069063, -0.025938, 0.006250, 0.038125, 0.090000, 0.076250, 0.145625, 0.177812, 0.239062, 0.296562, 0.330937, 0.386562, 0.412187, 0.471562, 0.538750, 0.625000, 0.701250
|
||||
#*# 0.038750, 0.005312, -0.043750, -0.070938, -0.087500, -0.061563, -0.100313, -0.099063, -0.081563, -0.073125, -0.070313, -0.038125, -0.006563, -0.009375, 0.021250, 0.057187, 0.083437, 0.161875, 0.189375, 0.238437, 0.285312, 0.346250, 0.384687, 0.427187, 0.532812, 0.580000, 0.667187, 0.739687
|
||||
#*# 0.035000, 0.000312, -0.009688, -0.063750, -0.027188, -0.044063, -0.045313, -0.067500, -0.014688, -0.045313, -0.015625, 0.004375, 0.017187, 0.038125, 0.069687, 0.104375, 0.177187, 0.199062, 0.236250, 0.325000, 0.330312, 0.398437, 0.446562, 0.523125, 0.562187, 0.621250, 0.686562, 0.782187
|
||||
#*# 0.047500, -0.008438, -0.017500, 0.002812, 0.025625, -0.002188, -0.050313, 0.017500, -0.025938, 0.021875, 0.027812, 0.022812, 0.071250, 0.103750, 0.145937, 0.174687, 0.198125, 0.264687, 0.277812, 0.383750, 0.398125, 0.462812, 0.482812, 0.558125, 0.605937, 0.645312, 0.728437, 0.781250
|
||||
#*# 0.129375, 0.089687, 0.057500, 0.059062, 0.052187, 0.056562, 0.062500, 0.054687, 0.095937, 0.090625, 0.134687, 0.134687, 0.176562, 0.196875, 0.223750, 0.305000, 0.295312, 0.349375, 0.398125, 0.429375, 0.495000, 0.539062, 0.579687, 0.630312, 0.691562, 0.709375, 0.798750, 0.873750
|
||||
#*# 0.200000, 0.209062, 0.191562, 0.141875, 0.185312, 0.148437, 0.186875, 0.150625, 0.192187, 0.193750, 0.232812, 0.256250, 0.286250, 0.311562, 0.362500, 0.392500, 0.420937, 0.434687, 0.519687, 0.542812, 0.584375, 0.596875, 0.697812, 0.702500, 0.776562, 0.834375, 0.890312, 0.994375
|
||||
#*# 0.283125, 0.290000, 0.252500, 0.257187, 0.282812, 0.249687, 0.296250, 0.315625, 0.312812, 0.328437, 0.360625, 0.424062, 0.406250, 0.454375, 0.492187, 0.525312, 0.544062, 0.614375, 0.626562, 0.675625, 0.685937, 0.756250, 0.810312, 0.850000, 0.889687, 0.947812, 1.011250, 1.059687
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 13
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 28
|
||||
#*# max_y = 459.96
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.82
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 19.661
|
||||
#*# pid_ki = 0.819
|
||||
#*# pid_kd = 117.969
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 64.455
|
||||
#*# pid_ki = 1.659
|
||||
#*# pid_kd = 626.020
|
||||
Loading…
Reference in New Issue