first backup
This commit is contained in:
hubfeenix
parent
e03dda3ba1
commit
d0708c3b12
@ -7,13 +7,7 @@ cors_domains =
|
||||
http://*.lan
|
||||
trusted_clients =
|
||||
127.0.0.1
|
||||
10.0.0.0/8
|
||||
127.0.0.0/8
|
||||
169.254.0.0/16
|
||||
172.16.0.0/12
|
||||
192.168.0.0/16
|
||||
FE80::/10
|
||||
::1/128
|
||||
10.40.0.0/16
|
||||
|
||||
[server]
|
||||
host = 0.0.0.0
|
||||
|
||||
@ -12,10 +12,4 @@ cors_domains:
|
||||
http://*.lan
|
||||
trusted_clients:
|
||||
127.0.0.1
|
||||
10.0.0.0/8
|
||||
127.0.0.0/8
|
||||
169.254.0.0/16
|
||||
172.16.0.0/12
|
||||
192.168.0.0/16
|
||||
FE80::/10
|
||||
::1/128
|
||||
10.40.0.0/16
|
||||
|
||||
324
printer-20220606_175323.cfg
Normal file
324
printer-20220606_175323.cfg
Normal file
@ -0,0 +1,324 @@
|
||||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 285
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "primeline"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 200
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
z_offset: 3.250 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
control: pid
|
||||
pid_kp: 28.413
|
||||
pid_ki: 1.334
|
||||
pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
control: pid
|
||||
pid_Kp: 22.2
|
||||
pid_Ki: 1.08
|
||||
pid_Kd: 114
|
||||
|
||||
|
||||
[gcode_macro _START_PRINT_AFTER_HEATING_BED]
|
||||
gcode:
|
||||
{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
|
||||
M117 Pre-heating extruder...
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
M104 S150
|
||||
TEMPERATURE_WAIT SENSOR=extruder MINIMUM=150
|
||||
{% endif %}
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 20,20
|
||||
mesh_max:465,460
|
||||
probe_count: 7,7
|
||||
fade_start: 1.0
|
||||
fade_end: 10.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*#
|
||||
#*# [bed_mesh vcore]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.146250, -0.580313, -0.993438, -1.390000, -1.680625
|
||||
#*# 0.458125, -0.109688, -0.498750, -0.825938, -1.111250
|
||||
#*# 0.674375, 0.189687, -0.035313, -0.261250, -0.505000
|
||||
#*# 1.180937, 0.899687, 0.665000, 0.499375, 0.222500
|
||||
#*# 2.068437, 1.804375, 1.605000, 1.387500, 1.222187
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.665625, 0.318437, 0.321250, 0.343125, 0.492500
|
||||
#*# 0.355000, 0.167187, 0.182187, 0.291250, 0.432187
|
||||
#*# -0.072813, -0.134063, 0.024687, 0.226562, 0.419062
|
||||
#*# -0.187813, -0.070938, 0.104375, 0.360312, 0.524062
|
||||
#*# 0.080937, 0.189687, 0.425000, 0.623750, 0.892500
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [bed_mesh ratos]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.658750, 0.348437, 0.369062, 0.392500, 0.536250
|
||||
#*# 0.306562, 0.168125, 0.214375, 0.328750, 0.452812
|
||||
#*# -0.138750, -0.135625, 0.045312, 0.248125, 0.420000
|
||||
#*# -0.223750, -0.061875, 0.141250, 0.383437, 0.531250
|
||||
#*# 0.079375, 0.220000, 0.478750, 0.668750, -0.534063
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
325
printer-20220607_133547.cfg
Normal file
325
printer-20220607_133547.cfg
Normal file
@ -0,0 +1,325 @@
|
||||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 285
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "primeline"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 200
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
control: pid
|
||||
pid_kp: 28.413
|
||||
pid_ki: 1.334
|
||||
pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
control: pid
|
||||
pid_Kp: 22.2
|
||||
pid_Ki: 1.08
|
||||
pid_Kd: 114
|
||||
|
||||
|
||||
[gcode_macro _START_PRINT_AFTER_HEATING_BED]
|
||||
gcode:
|
||||
{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
|
||||
M117 Pre-heating extruder...
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
M104 S150
|
||||
TEMPERATURE_WAIT SENSOR=extruder MINIMUM=150
|
||||
{% endif %}
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 20,20
|
||||
mesh_max:465,460
|
||||
probe_count: 7,7
|
||||
fade_start: 1.0
|
||||
fade_end: 10.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*#
|
||||
#*# [bed_mesh vcore]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.146250, -0.580313, -0.993438, -1.390000, -1.680625
|
||||
#*# 0.458125, -0.109688, -0.498750, -0.825938, -1.111250
|
||||
#*# 0.674375, 0.189687, -0.035313, -0.261250, -0.505000
|
||||
#*# 1.180937, 0.899687, 0.665000, 0.499375, 0.222500
|
||||
#*# 2.068437, 1.804375, 1.605000, 1.387500, 1.222187
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# -0.235313, -0.193125, -0.027813, 0.191875, 0.476875, 0.754062, 1.087812
|
||||
#*# -0.378125, -0.287188, -0.063438, 0.204375, 0.473125, 0.758125, 1.094375
|
||||
#*# -0.641250, -0.455000, -0.162813, 0.093437, 0.465000, 0.760000, 1.108750
|
||||
#*# -0.817188, -0.576875, -0.252188, 0.101562, 0.465625, 0.779375, 1.198437
|
||||
#*# -0.790938, -0.513750, -0.152188, 0.205312, 0.618750, 0.991875, 1.332187
|
||||
#*# -0.656875, -0.310625, 0.096250, 0.469375, 0.854062, 1.195625, 1.360000
|
||||
#*# -0.368750, -0.051563, 0.107500, 0.780625, 1.135000, 1.506562, 1.395312
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 20.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 7
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 20.0
|
||||
#*# x_count = 7
|
||||
#*# max_y = 459.98
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.96
|
||||
#*#
|
||||
#*# [bed_mesh ratos]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.658750, 0.348437, 0.369062, 0.392500, 0.536250
|
||||
#*# 0.306562, 0.168125, 0.214375, 0.328750, 0.452812
|
||||
#*# -0.138750, -0.135625, 0.045312, 0.248125, 0.420000
|
||||
#*# -0.223750, -0.061875, 0.141250, 0.383437, 0.531250
|
||||
#*# 0.079375, 0.220000, 0.478750, 0.668750, -0.534063
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
325
printer-20220607_140915.cfg
Normal file
325
printer-20220607_140915.cfg
Normal file
@ -0,0 +1,325 @@
|
||||
# Rat Rig V-core 3 Klipper Config
|
||||
# Documentation: https://os.ratrig.com
|
||||
|
||||
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
||||
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
||||
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
||||
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
||||
|
||||
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
||||
|
||||
#############################################################################################################
|
||||
### CONTROL BOARD
|
||||
### Pick the board you have installed and wired in your printer.
|
||||
#############################################################################################################
|
||||
[include config/boards/btt-octopus-11/config.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### BASE SETUP
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/v-core-3.cfg]
|
||||
|
||||
#############################################################################################################
|
||||
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
||||
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
||||
#############################################################################################################
|
||||
[include config/printers/v-core-3/steppers.cfg]
|
||||
|
||||
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
||||
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
||||
|
||||
|
||||
[include config/printers/v-core-3/tmc2209.cfg]
|
||||
|
||||
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### HOMING
|
||||
### Pick your probe and endstops
|
||||
#############################################################################################################
|
||||
# BL Touch
|
||||
[include config/z-probe/bltouch.cfg]
|
||||
|
||||
|
||||
# Physical endstops
|
||||
[include config/printers/v-core-3/physical-endstops.cfg]
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PHYSICAL DIMENSIONS
|
||||
### Pick your printer size
|
||||
#############################################################################################################
|
||||
|
||||
[include config/printers/v-core-3/500.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### extruder and hotend
|
||||
#############################################################################################################
|
||||
|
||||
[extruder]
|
||||
rotation_distance: 4.63
|
||||
full_steps_per_rotation: 200
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_velocity: 60
|
||||
max_extrude_only_distance: 200
|
||||
nozzle_diameter: 0.4
|
||||
heater_pin: e_heater_pin
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: e_sensor_pin
|
||||
min_extrude_temp: 170
|
||||
min_temp: 0
|
||||
max_temp: 285
|
||||
pressure_advance: 0.05
|
||||
|
||||
[tmc2209 extruder]
|
||||
run_current: 0.35
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[firmware_retraction]
|
||||
retract_speed: 60
|
||||
unretract_extra_length: 0
|
||||
unretract_speed: 60
|
||||
retract_length: 0.5
|
||||
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACROS
|
||||
#############################################################################################################
|
||||
[include config/macros.cfg]
|
||||
[include config/shell-macros.cfg]
|
||||
[include config/printers/v-core-3/macros.cfg]
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### MACRO CONFIGURATION
|
||||
### Configure the behavior of RatOS macros
|
||||
#############################################################################################################
|
||||
[gcode_macro RatOS]
|
||||
# Use absolute extrusion mode
|
||||
# Set to True to use relative extrusion mode
|
||||
variable_relative_extrusion: False
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
# Set to False to disable
|
||||
variable_preheat_extruder: True
|
||||
# Calibrate the bed mesh in the START_PRINT macro.
|
||||
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
||||
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
||||
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
||||
variable_calibrate_bed_mesh: True
|
||||
# Print a prime line or blob at the end of the START_PRINT macro
|
||||
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
||||
variable_nozzle_priming: "primeline"
|
||||
# Park in the back when waiting for the extruder to heat up
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_start_print_park_in: "back"
|
||||
# Height to park it when waiting for extruder to heat.
|
||||
variable_start_print_park_z_height: 50
|
||||
# Skew profile to load before starting the print
|
||||
# uncomment this to use your calibrated skew correction profile.
|
||||
#variable_skew_profile: "my_skew_profile"
|
||||
# Park in the back after the print has ended or was cancelled.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_end_print_park_in: "back"
|
||||
# Park in the back when the print is paused.
|
||||
# set to "front" to park in the front, or "center" to park in the center.
|
||||
variable_pause_print_park_in: "back"
|
||||
# Set the speed for travel moves in RatOS Macros in mm/s.
|
||||
variable_macro_travel_speed: 200
|
||||
|
||||
|
||||
#############################################################################################################
|
||||
### PRINTER CONFIGURATION
|
||||
### Customize the defaults to your specific build
|
||||
#############################################################################################################
|
||||
[stepper_x]
|
||||
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 0 # Adjust this to your setup
|
||||
#x_offset: -27.0
|
||||
|
||||
|
||||
|
||||
[stepper_y]
|
||||
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
||||
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
||||
position_endstop: 480 # 300mm printer
|
||||
position_min: 5
|
||||
#y_offset: -21.0
|
||||
|
||||
|
||||
#position_endstop: 400 # 400mm printer
|
||||
#position_endstop: 500 # 500mm printer
|
||||
|
||||
[stepper_z]
|
||||
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z1]
|
||||
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
[stepper_z2]
|
||||
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
||||
rotation_distance: 4 # 4 for TR8*4 lead screws
|
||||
endstop_pin: probe: z_virtual_endstop
|
||||
|
||||
#Z Probe configuration
|
||||
[bltouch]
|
||||
sensor_pin: ^PB7
|
||||
control_pin: PB6
|
||||
x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
||||
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
||||
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
||||
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
||||
|
||||
# Safe Z Home (Physical endstops only)
|
||||
[safe_z_home]
|
||||
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
||||
speed: 50
|
||||
z_hop: 10 # Move up 10mm
|
||||
z_hop_speed: 5
|
||||
|
||||
#ORIGINAL
|
||||
#home_xy_position: 150,150 # 300mm printer
|
||||
#home_xy_position: 200,200 # 400mm printer
|
||||
#home_xy_position: 250,250 # 500mm printer
|
||||
|
||||
[extruder]
|
||||
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
||||
#pressure_advance: 0.05
|
||||
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
||||
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
||||
control: pid
|
||||
pid_kp: 28.413
|
||||
pid_ki: 1.334
|
||||
pid_kd: 151.300
|
||||
|
||||
[heater_bed]
|
||||
control: pid
|
||||
pid_Kp: 22.2
|
||||
pid_Ki: 1.08
|
||||
pid_Kd: 114
|
||||
|
||||
|
||||
[gcode_macro _START_PRINT_AFTER_HEATING_BED]
|
||||
gcode:
|
||||
{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
|
||||
M117 Pre-heating extruder...
|
||||
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
||||
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
||||
M104 S150
|
||||
TEMPERATURE_WAIT SENSOR=extruder MINIMUM=150
|
||||
{% endif %}
|
||||
|
||||
# [bed_mesh]
|
||||
# speed: 30
|
||||
# horizontal_move_z: 10
|
||||
# mesh_min: 15, 15
|
||||
# mesh_max: 450, 450
|
||||
# probe_count: 5 , 5
|
||||
|
||||
[bed_mesh]
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 20,20
|
||||
mesh_max:465,460
|
||||
probe_count: 7,7
|
||||
fade_start: 1.0
|
||||
fade_end: 10.0
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: .2
|
||||
|
||||
#############################################################################################################
|
||||
### INPUT SHAPER
|
||||
### Enable/disable input shaper calibration
|
||||
#############################################################################################################
|
||||
# Uncomment this next line if you have an ADXL345 connected to your control board
|
||||
#[include config/printers/v-core-3/input-shaper.cfg]
|
||||
|
||||
# ADXL345 resonance testing configuration
|
||||
#[resonance_tester]
|
||||
#probe_points:
|
||||
# 150,150,20 # 300mm printer
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*#
|
||||
#*# [bed_mesh vcore]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.146250, -0.580313, -0.993438, -1.390000, -1.680625
|
||||
#*# 0.458125, -0.109688, -0.498750, -0.825938, -1.111250
|
||||
#*# 0.674375, 0.189687, -0.035313, -0.261250, -0.505000
|
||||
#*# 1.180937, 0.899687, 0.665000, 0.499375, 0.222500
|
||||
#*# 2.068437, 1.804375, 1.605000, 1.387500, 1.222187
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.076994, -0.084569, -0.111131, -0.102694, -0.081444, -0.037381, 0.026994
|
||||
#*# -0.119569, -0.203631, -0.207069, -0.183006, -0.136756, -0.085194, 0.025119
|
||||
#*# -0.448006, -0.488944, -0.417381, -0.373319, -0.235819, -0.161131, -0.018631
|
||||
#*# -0.689256, -0.702069, -0.599569, -0.460194, -0.332069, -0.228006, -0.039881
|
||||
#*# -0.778944, -0.676444, -0.572381, -0.391756, -0.245194, -0.123631, -0.011444
|
||||
#*# -0.694881, -0.585194, -0.413631, -0.256131, -0.088944, 0.020744, 0.171369
|
||||
#*# -0.536444, -0.409569, -0.210819, -0.007381, 0.111369, 0.250119, 0.395119
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 20.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 7
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 20.0
|
||||
#*# x_count = 7
|
||||
#*# max_y = 459.98
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 464.96
|
||||
#*#
|
||||
#*# [bed_mesh ratos]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.658750, 0.348437, 0.369062, 0.392500, 0.536250
|
||||
#*# 0.306562, 0.168125, 0.214375, 0.328750, 0.452812
|
||||
#*# -0.138750, -0.135625, 0.045312, 0.248125, 0.420000
|
||||
#*# -0.223750, -0.061875, 0.141250, 0.383437, 0.531250
|
||||
#*# 0.079375, 0.220000, 0.478750, 0.668750, -0.534063
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
40
printer.cfg
40
printer.cfg
@ -179,8 +179,8 @@ x_offset: -27.0
|
||||
y_offset: -21.0
|
||||
#pin_up_touch_mode_reports_triggered: True
|
||||
pin_move_time: 0.8
|
||||
#z_offset: 3.250 # USE FOR PLA
|
||||
z_offset: 2.75 # USE FOR PETG
|
||||
#z_offset: 3.20 # USE FOR PLA
|
||||
#z_offset: 2.75 # USE FOR PETG
|
||||
|
||||
# [probe]
|
||||
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
||||
@ -260,11 +260,11 @@ bicubic_tension: .2
|
||||
# 200,200,20 # 400mm printer
|
||||
# 250,250,20 # 500mm printer
|
||||
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 3.000
|
||||
#*#
|
||||
#*# [bed_mesh vcore]
|
||||
#*# version = 1
|
||||
@ -288,30 +288,32 @@ bicubic_tension: .2
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.665625, 0.318437, 0.321250, 0.343125, 0.492500
|
||||
#*# 0.355000, 0.167187, 0.182187, 0.291250, 0.432187
|
||||
#*# -0.072813, -0.134063, 0.024687, 0.226562, 0.419062
|
||||
#*# -0.187813, -0.070938, 0.104375, 0.360312, 0.524062
|
||||
#*# 0.080937, 0.189687, 0.425000, 0.623750, 0.892500
|
||||
#*# 0.076994, -0.084569, -0.111131, -0.102694, -0.081444, -0.037381, 0.026994
|
||||
#*# -0.119569, -0.203631, -0.207069, -0.183006, -0.136756, -0.085194, 0.025119
|
||||
#*# -0.448006, -0.488944, -0.417381, -0.373319, -0.235819, -0.161131, -0.018631
|
||||
#*# -0.689256, -0.702069, -0.599569, -0.460194, -0.332069, -0.228006, -0.039881
|
||||
#*# -0.778944, -0.676444, -0.572381, -0.391756, -0.245194, -0.123631, -0.011444
|
||||
#*# -0.694881, -0.585194, -0.413631, -0.256131, -0.088944, 0.020744, 0.171369
|
||||
#*# -0.536444, -0.409569, -0.210819, -0.007381, 0.111369, 0.250119, 0.395119
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# min_x = 20.0
|
||||
#*# algo = bicubic
|
||||
#*# y_count = 5
|
||||
#*# y_count = 7
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 15.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 450.0
|
||||
#*# min_y = 20.0
|
||||
#*# x_count = 7
|
||||
#*# max_y = 459.98
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 450.0
|
||||
#*# max_x = 464.96
|
||||
#*#
|
||||
#*# [bed_mesh ratos]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.658750, 0.348437, 0.369062, 0.392500, 0.536250
|
||||
#*# 0.306562, 0.168125, 0.214375, 0.328750, 0.452812
|
||||
#*# -0.138750, -0.135625, 0.045312, 0.248125, 0.420000
|
||||
#*# -0.223750, -0.061875, 0.141250, 0.383437, 0.531250
|
||||
#*# 0.079375, 0.220000, 0.478750, 0.668750, -0.534063
|
||||
#*# 0.658750, 0.348437, 0.369062, 0.392500, 0.536250
|
||||
#*# 0.306562, 0.168125, 0.214375, 0.328750, 0.452812
|
||||
#*# -0.138750, -0.135625, 0.045312, 0.248125, 0.420000
|
||||
#*# -0.223750, -0.061875, 0.141250, 0.383437, 0.531250
|
||||
#*# 0.079375, 0.220000, 0.478750, 0.668750, -0.534063
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 15.0
|
||||
#*# algo = bicubic
|
||||
|
||||
Loading…
Reference in New Issue
Block a user