340 lines
12 KiB
INI
340 lines
12 KiB
INI
# Rat Rig V-core 3 Klipper Config
|
|
# Documentation: https://os.ratrig.com
|
|
|
|
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
|
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
|
# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
|
|
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
|
|
|
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
|
|
|
|
|
#############################################################################################################
|
|
### CONTROL BOARD
|
|
### Pick the board you have installed and wired in your printer.
|
|
#############################################################################################################
|
|
[include config/boards/btt-octopus-11/config.cfg]
|
|
|
|
#############################################################################################################
|
|
### BASE SETUP
|
|
#############################################################################################################
|
|
[include config/printers/v-core-3/v-core-3.cfg]
|
|
[printer]
|
|
max_velocity: 150
|
|
max_accel: 500
|
|
max_accel_to_decel: 500
|
|
max_z_velocity: 15
|
|
max_z_accel: 20
|
|
|
|
|
|
#############################################################################################################
|
|
### STEPPER MOTORS, DRIVERS & SPEED LIMITS
|
|
### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
|
|
#############################################################################################################
|
|
[include config/printers/v-core-3/steppers.cfg]
|
|
|
|
# UNCOOLED TMC 2209 + LDO-42STH48-2504AC
|
|
[include config/printers/v-core-3/speed-limits-basic.cfg]
|
|
|
|
|
|
[include config/printers/v-core-3/tmc2209.cfg]
|
|
|
|
[include config/steppers/ldo/42sth48-2504ac/2209/24v-1.1a-*.cfg]
|
|
|
|
|
|
|
|
#############################################################################################################
|
|
### HOMING
|
|
### Pick your probe and endstops
|
|
#############################################################################################################
|
|
# BL Touch
|
|
[include config/z-probe/bltouch.cfg]
|
|
|
|
|
|
# Physical endstops
|
|
[include config/printers/v-core-3/physical-endstops.cfg]
|
|
|
|
|
|
|
|
#############################################################################################################
|
|
### PHYSICAL DIMENSIONS
|
|
### Pick your printer size
|
|
#############################################################################################################
|
|
|
|
[include config/printers/v-core-3/500.cfg]
|
|
|
|
|
|
#############################################################################################################
|
|
### extruder and hotend
|
|
#############################################################################################################
|
|
|
|
[extruder]
|
|
rotation_distance: 4.63
|
|
full_steps_per_rotation: 200
|
|
filament_diameter: 1.750
|
|
max_extrude_only_velocity: 60
|
|
max_extrude_only_distance: 200
|
|
nozzle_diameter: 0.4
|
|
heater_pin: e_heater_pin
|
|
sensor_type: ATC Semitec 104GT-2
|
|
sensor_pin: e_sensor_pin
|
|
min_extrude_temp: 170
|
|
min_temp: 0
|
|
max_temp: 400
|
|
pressure_advance: 0.05
|
|
|
|
[tmc2209 extruder]
|
|
run_current: 0.35
|
|
stealthchop_threshold: 0
|
|
|
|
[firmware_retraction]
|
|
retract_speed: 60
|
|
unretract_extra_length: 0
|
|
unretract_speed: 60
|
|
retract_length: 0.5
|
|
|
|
|
|
|
|
#############################################################################################################
|
|
### MACROS
|
|
#############################################################################################################
|
|
[include config/macros.cfg]
|
|
[include config/shell-macros.cfg]
|
|
[include config/printers/v-core-3/macros.cfg]
|
|
|
|
|
|
#############################################################################################################
|
|
### MACRO CONFIGURATION
|
|
### Configure the behavior of RatOS macros
|
|
#############################################################################################################
|
|
[gcode_macro RatOS]
|
|
# Use absolute extrusion mode
|
|
# Set to True to use relative extrusion mode
|
|
variable_relative_extrusion: False
|
|
# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
|
|
# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
|
|
# Set to False to disable
|
|
variable_preheat_extruder: True
|
|
# Calibrate the bed mesh in the START_PRINT macro.
|
|
# Set to false to skip BED_MESH_CALIBRATE, it will still load the BED_MESH
|
|
# with the name "ratos", be sure to save your bed_mesh profile with that name.
|
|
# or override the _START_PRINT_BED_MESH macro to implement your own mesh handling logic.
|
|
variable_calibrate_bed_mesh: True
|
|
# Print a prime line or blob at the end of the START_PRINT macro
|
|
# set to "primeline" or "primeblob", or False to disable nozzle_priming.
|
|
variable_nozzle_priming: "false"
|
|
# Park in the back when waiting for the extruder to heat up
|
|
# set to "front" to park in the front, or "center" to park in the center.
|
|
variable_start_print_park_in: "back"
|
|
# Height to park it when waiting for extruder to heat.
|
|
variable_start_print_park_z_height: 50
|
|
# Skew profile to load before starting the print
|
|
# uncomment this to use your calibrated skew correction profile.
|
|
#variable_skew_profile: "my_skew_profile"
|
|
# Park in the back after the print has ended or was cancelled.
|
|
# set to "front" to park in the front, or "center" to park in the center.
|
|
variable_end_print_park_in: "back"
|
|
# Park in the back when the print is paused.
|
|
# set to "front" to park in the front, or "center" to park in the center.
|
|
variable_pause_print_park_in: "back"
|
|
# Set the speed for travel moves in RatOS Macros in mm/s.
|
|
variable_macro_travel_speed: 100
|
|
|
|
|
|
#############################################################################################################
|
|
### PRINTER CONFIGURATION
|
|
### Customize the defaults to your specific build
|
|
#############################################################################################################
|
|
[stepper_x]
|
|
dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction
|
|
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
|
position_endstop: 0 # Adjust this to your setup
|
|
#x_offset: -27.0
|
|
|
|
|
|
|
|
[stepper_y]
|
|
dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction
|
|
rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys
|
|
position_endstop: 480 # 300mm printer
|
|
position_min: 5
|
|
#y_offset: -21.0
|
|
|
|
|
|
#position_endstop: 400 # 400mm printer
|
|
#position_endstop: 500 # 500mm printer
|
|
|
|
[stepper_z]
|
|
dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction
|
|
rotation_distance: 4 # 4 for TR8*4 lead screws
|
|
endstop_pin: probe: z_virtual_endstop
|
|
|
|
[stepper_z1]
|
|
dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction
|
|
rotation_distance: 4 # 4 for TR8*4 lead screws
|
|
endstop_pin: probe: z_virtual_endstop
|
|
|
|
[stepper_z2]
|
|
dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction
|
|
rotation_distance: 4 # 4 for TR8*4 lead screws
|
|
endstop_pin: probe: z_virtual_endstop
|
|
|
|
#Z Probe configuration
|
|
[bltouch]
|
|
sensor_pin: ^PB7
|
|
control_pin: PB6
|
|
x_offset: -27.0
|
|
y_offset: -21.0
|
|
#pin_up_touch_mode_reports_triggered: True
|
|
pin_move_time: 0.8
|
|
#z_offset: 3.20 # USE FOR PLA
|
|
#z_offset: 2.75 # USE FOR PETG
|
|
|
|
# [probe]
|
|
# z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder!
|
|
# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes.
|
|
#pin: ^!probe_pin # NPN NO (refer to the specs on your probe)
|
|
#pin: probe_pin # PNP NO (refer to the specs on your probe)
|
|
#pin: !probe_pin # PNP NC (refer to the specs on your probe)
|
|
|
|
# Safe Z Home (Physical endstops only)
|
|
[safe_z_home]
|
|
home_xy_position: 250, 250 # Change coordinates to the center of your print bed
|
|
speed: 50
|
|
z_hop: 10 # Move up 10mm
|
|
z_hop_speed: 5
|
|
|
|
#ORIGINAL
|
|
#home_xy_position: 150,150 # 300mm printer
|
|
#home_xy_position: 200,200 # 400mm printer
|
|
#home_xy_position: 250,250 # 500mm printer
|
|
|
|
[extruder]
|
|
# Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning.
|
|
#pressure_advance: 0.05
|
|
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
|
dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction
|
|
#control: pid
|
|
#pid_kp: 28.413
|
|
#pid_ki: 1.334
|
|
#pid_kd: 151.300
|
|
|
|
[heater_bed]
|
|
#control: pid
|
|
#pid_Kp: 22.2
|
|
#pid_Ki: 1.08
|
|
#pid_Kd: 114
|
|
|
|
|
|
# [bed_mesh]
|
|
# speed: 30
|
|
# horizontal_move_z: 10
|
|
# mesh_min: 15, 15
|
|
# mesh_max: 450, 450
|
|
# probe_count: 5 , 5
|
|
|
|
[bed_mesh]
|
|
horizontal_move_z: 5
|
|
mesh_min: 28,21
|
|
mesh_max:465,460
|
|
probe_count: 10,10
|
|
fade_start: 5.0
|
|
fade_end: 100.0
|
|
mesh_pps: 2,2
|
|
algorithm: bicubic
|
|
bicubic_tension: .2
|
|
|
|
#############################################################################################################
|
|
### INPUT SHAPER
|
|
### Enable/disable input shaper calibration
|
|
#############################################################################################################
|
|
# Uncomment this next line if you have an ADXL345 connected to your control board
|
|
#[include config/printers/v-core-3/input-shaper.cfg]
|
|
|
|
# ADXL345 resonance testing configuration
|
|
#[resonance_tester]
|
|
#probe_points:
|
|
# 150,150,20 # 300mm printer
|
|
# 200,200,20 # 400mm printer
|
|
# 250,250,20 # 500mm printer
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [bltouch]
|
|
#*# z_offset = 2.940
|
|
#*#
|
|
#*# [bed_mesh vcore]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.146250, -0.580313, -0.993438, -1.390000, -1.680625
|
|
#*# 0.458125, -0.109688, -0.498750, -0.825938, -1.111250
|
|
#*# 0.674375, 0.189687, -0.035313, -0.261250, -0.505000
|
|
#*# 1.180937, 0.899687, 0.665000, 0.499375, 0.222500
|
|
#*# 2.068437, 1.804375, 1.605000, 1.387500, 1.222187
|
|
#*# tension = 0.2
|
|
#*# min_x = 15.0
|
|
#*# algo = bicubic
|
|
#*# y_count = 5
|
|
#*# mesh_y_pps = 2
|
|
#*# min_y = 15.0
|
|
#*# x_count = 5
|
|
#*# max_y = 450.0
|
|
#*# mesh_x_pps = 2
|
|
#*# max_x = 450.0
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.533437, 0.361250, 0.195625, 0.148125, 0.168437, 0.198750, 0.254375, 0.394687, 0.470000, 0.663750
|
|
#*# 0.464375, 0.308125, 0.186250, 0.162187, 0.154062, 0.194687, 0.283750, 0.416562, 0.533437, 0.690625
|
|
#*# 0.335625, 0.186562, 0.084375, 0.101875, 0.095625, 0.139687, 0.255625, 0.379062, 0.492812, 0.649375
|
|
#*# 0.163125, 0.040312, -0.005000, 0.029062, 0.036250, 0.114687, 0.214062, 0.336875, 0.463125, 0.666250
|
|
#*# 0.022500, -0.036875, -0.090938, -0.067813, -0.002188, 0.077500, 0.226250, 0.311562, 0.481250, 0.674062
|
|
#*# -0.065625, -0.113438, -0.108750, -0.085000, -0.002813, 0.085625, 0.188750, 0.347187, 0.504375, 0.694687
|
|
#*# -0.044375, -0.024375, -0.064375, -0.008125, 0.058750, 0.168437, 0.275000, 0.425937, 0.577812, 0.791562
|
|
#*# 0.070000, 0.032187, 0.065000, 0.100000, 0.171875, 0.293437, 0.395625, 0.556250, 0.718125, 0.880312
|
|
#*# 0.168750, 0.176562, 0.175937, 0.230937, 0.366250, 0.462812, 0.555000, 0.686562, 0.813437, 0.993125
|
|
#*# 0.335312, 0.349375, 0.385000, 0.460312, 0.522187, 0.619062, 0.747500, 0.842187, 1.026250, 1.203125
|
|
#*# tension = 0.2
|
|
#*# min_x = 28.0
|
|
#*# algo = bicubic
|
|
#*# y_count = 10
|
|
#*# mesh_y_pps = 2
|
|
#*# min_y = 21.0
|
|
#*# x_count = 10
|
|
#*# max_y = 459.93
|
|
#*# mesh_x_pps = 2
|
|
#*# max_x = 464.95
|
|
#*#
|
|
#*# [bed_mesh ratos]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.658750, 0.348437, 0.369062, 0.392500, 0.536250
|
|
#*# 0.306562, 0.168125, 0.214375, 0.328750, 0.452812
|
|
#*# -0.138750, -0.135625, 0.045312, 0.248125, 0.420000
|
|
#*# -0.223750, -0.061875, 0.141250, 0.383437, 0.531250
|
|
#*# 0.079375, 0.220000, 0.478750, 0.668750, -0.534063
|
|
#*# tension = 0.2
|
|
#*# min_x = 15.0
|
|
#*# algo = bicubic
|
|
#*# y_count = 5
|
|
#*# mesh_y_pps = 2
|
|
#*# min_y = 15.0
|
|
#*# x_count = 5
|
|
#*# max_y = 450.0
|
|
#*# mesh_x_pps = 2
|
|
#*# max_x = 450.0
|
|
#*#
|
|
#*# [extruder]
|
|
#*# control = pid
|
|
#*# pid_kp = 19.661
|
|
#*# pid_ki = 0.819
|
|
#*# pid_kd = 117.969
|
|
#*#
|
|
#*# [heater_bed]
|
|
#*# control = pid
|
|
#*# pid_kp = 64.455
|
|
#*# pid_ki = 1.659
|
|
#*# pid_kd = 626.020
|