From fda68e3deec4c2c0da2c8dd3faf5f1848e4ce16f Mon Sep 17 00:00:00 2001 From: Torsten Date: Mon, 30 Jan 2023 14:53:28 +0200 Subject: [PATCH] pin substitutions --- printer.cfg | 152 +++++++++++++++++++--------------------------------- 1 file changed, 55 insertions(+), 97 deletions(-) diff --git a/printer.cfg b/printer.cfg index 1f8f294..4f906be 100644 --- a/printer.cfg +++ b/printer.cfg @@ -8,55 +8,22 @@ # Read more about klipper here: https://www.klipper3d.org/Overview.html - -############################################################################################################# -### CONTROL BOARD -### Pick the board you have installed and wired in your printer. -############################################################################################################# -# not all aliases are set yet, but diag pins my be usefull in future (i.e detecting skipped steps on extruder) -[board_pins octopus_11_tmc2209] -aliases: -# steppers - x_step_pin=PF13, x_dir_pin=PF12, x_enable_pin=PF14, x_uart_pin=PC4, x_diag_pin=PG6, x_endstop_pin=PG6, - y_step_pin=PG0, y_dir_pin=PG1, y_enable_pin=PF15, y_uart_pin=PD11, y_diag_pin=PG9, y_endstop_pin=PG9, - z0_step_pin=PC13, z0_dir_pin=PF0, z0_enable_pin=PF1, z0_uart_pin=PE4, z0_diag_pin=null, - z1_step_pin=PE2, z1_dir_pin=PE3, z1_enable_pin=PD4, z1_uart_pin=PE1, z1_diag_pin=null, - z2_step_pin=PE6, z2_dir_pin=PA14, z2_enable_pin=PE0, z2_uart_pin=PD3, z2_diag_pin=null, - e_step_pin=PF11, e_dir_pin=PG3, e_enable_pin=PG5, e_uart_pin=PC6, e_diag_pin=null, e_heater_pin=PA2, e_sensor_pin=PF4, -# accel - adxl345_cs_pin=PA15, -# auto leveling - bltouch_sensor_pin=PB7, bltouch_control_pin=PB6, - probe_pin=PB7, -# fans - fan_part_cooling_pin=PA8, - fan_toolhead_cooling_pin=PE5, - fan_controller_board_pin=PD12, -# Bed heater - heater_bed_heating_pin=PA1, - heater_bed_sensor_pin=PF3, - -## Expansion ports - # EXP1 header - EXP1_1=PE8, EXP1_3=PE9, EXP1_5=PE12, EXP1_7=PE14, EXP1_9=, - EXP1_2=PE7, EXP1_4=PE10, EXP1_6=PE13, EXP1_8=PE15, EXP1_10=<5V>, - # EXP2 header - EXP2_1=PA6, EXP2_3=PB1, EXP2_5=PB2, EXP2_7=PC15, EXP2_9=, - EXP2_2=PA5, EXP2_4=PA4, EXP2_6=PA7, EXP2_8=, EXP2_10=PC5, - # Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi2" - [mcu] baud: 250000 serial: /dev/btt-octopus-11 + [temperature_sensor Octopus] sensor_type: temperature_mcu min_temp: 0 max_temp: 100 +[temperature_sensor raspberry_pi] +sensor_type: temperature_host + [adxl345] spi_bus: spi3 -cs_pin: adxl345_cs_pin +cs_pin: PA15 ############################################################################################################# ### BASE SETUP @@ -73,9 +40,6 @@ gcode: # 2 hour timeout timeout: 7200 -[temperature_sensor raspberry_pi] -sensor_type: temperature_host - [skew_correction] [input_shaper] @@ -93,23 +57,23 @@ enable_force_move: True [respond] [heater_bed] -heater_pin: heater_bed_heating_pin -sensor_pin: heater_bed_sensor_pin +heater_pin: PA1 +sensor_pin: PF3 sensor_type: Generic 3950 min_temp: 0 max_temp: 120 pwm_cycle_time: 0.02 # 50hz for european AC, to avoid flickering lights. [fan] -pin: fan_part_cooling_pin +pin: PA8 shutdown_speed: 1.0 [heater_fan toolhead_cooling_fan] -pin: fan_toolhead_cooling_pin +pin: PE5 fan_speed: 1 [controller_fan controller_fan] -pin: fan_controller_board_pin +pin: PD12 # These are only safeguards for first time users # Modify printer.cfg to tune acceleration. @@ -134,18 +98,18 @@ max_z_accel: 20 ### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations. ############################################################################################################# [stepper_x] -step_pin: x_step_pin -dir_pin: x_dir_pin -enable_pin: !x_enable_pin +step_pin: PF13 +dir_pin: PF12 +enable_pin: !PF14 rotation_distance: 40 microsteps: 64 homing_speed: 50 homing_retract_dist: 0 [stepper_y] -step_pin: y_step_pin -dir_pin: y_dir_pin -enable_pin: !y_enable_pin +step_pin: PG0 +dir_pin: PG1 +enable_pin: !PF15 rotation_distance: 40 microsteps: 64 homing_speed: 50 @@ -153,32 +117,32 @@ homing_retract_dist: 0 [stepper_z] endstop_pin: probe:z_virtual_endstop -step_pin: z0_step_pin -dir_pin: z0_dir_pin -enable_pin: !z0_enable_pin +step_pin: PC13 +dir_pin: PF0 +enable_pin: !PF1 rotation_distance: 4 microsteps: 64 position_min: -5 # Needed for z-offset calibration and tilt_adjust. homing_speed: 10 [stepper_z1] -step_pin: z1_step_pin -dir_pin: z1_dir_pin -enable_pin: !z1_enable_pin +step_pin: PE2 +dir_pin: PE3 +enable_pin: !PD4 rotation_distance: 4 microsteps: 64 [stepper_z2] -step_pin: z2_step_pin -dir_pin: z2_dir_pin -enable_pin: !z2_enable_pin +step_pin: PE6 +dir_pin: PA14 +enable_pin: !PE0 rotation_distance: 4 microsteps: 64 [extruder] -step_pin: e_step_pin -dir_pin: !e_dir_pin -enable_pin: !e_enable_pin +step_pin: PF11 +dir_pin: !PG3 +enable_pin: !PG5 microsteps: 64 # UNCOOLED TMC 2209 + LDO-42STH48-2504AC @@ -199,7 +163,7 @@ square_corner_velocity: 5 # Backwards compatibility [tmc2209 stepper_x] -uart_pin: x_uart_pin +uart_pin: PC4 run_current: 1.1 stealthchop_threshold: 1 @@ -209,7 +173,7 @@ run_current: 1.1 stealthchop_threshold: 1 [tmc2209 extruder] -uart_pin: e_uart_pin +uart_pin: PC6 run_current: 0.5 stealthchop_threshold: 0 @@ -219,18 +183,18 @@ run_current: 1.0 stealthchop_threshold: 1 [tmc2209 stepper_z1] -uart_pin: z1_uart_pin +uart_pin: PE1 run_current: 1.1 stealthchop_threshold: 1 [tmc2209 stepper_z2] -uart_pin: z2_uart_pin +uart_pin: PD3 run_current: 1.0 stealthchop_threshold: 1 [tmc2209 stepper_x] -uart_pin: x_uart_pin +uart_pin: PC4 run_current: 1.1 stealthchop_threshold: 1 @@ -240,7 +204,7 @@ run_current: 1.1 stealthchop_threshold: 1 [tmc2209 extruder] -uart_pin: e_uart_pin +uart_pin: PC6 run_current: 0.5 stealthchop_threshold: 0 @@ -250,17 +214,17 @@ run_current: 1.0 stealthchop_threshold: 1 [tmc2209 stepper_z1] -uart_pin: z1_uart_pin +uart_pin: PE1 run_current: 1.1 stealthchop_threshold: 1 [tmc2209 stepper_z2] -uart_pin: z2_uart_pin +uart_pin: PD3 run_current: 1.0 stealthchop_threshold: 1 [tmc2209 stepper_x] -uart_pin: x_uart_pin +uart_pin: PC4 run_current: 1.1 driver_TBL: 1 driver_TOFF: 3 @@ -284,7 +248,7 @@ driver_HEND: 0 driver_HSTRT: 0 [tmc2209 stepper_z1] -uart_pin: z1_uart_pin +uart_pin: PE1 run_current: 1.1 driver_TBL: 1 driver_TOFF: 3 @@ -292,7 +256,7 @@ driver_HEND: 0 driver_HSTRT: 0 [tmc2209 stepper_z2] -uart_pin: z2_uart_pin +uart_pin: PD3 run_current: 1.1 driver_TBL: 1 driver_TOFF: 3 @@ -305,8 +269,8 @@ driver_HSTRT: 0 ############################################################################################################# # BL Touch [bltouch] -sensor_pin: ^bltouch_sensor_pin -control_pin: bltouch_control_pin +sensor_pin: ^PB7 +control_pin: PB6 speed: 7 pin_move_time: 0.675 sample_retract_dist: 10 @@ -318,11 +282,11 @@ y_offset: -13 # Physical endstops [stepper_x] -endstop_pin: x_endstop_pin +endstop_pin: PG6 homing_retract_dist: 5.0 [stepper_y] -endstop_pin: y_endstop_pin +endstop_pin: PG9 homing_positive_dir: true homing_retract_dist: 5.0 @@ -385,9 +349,9 @@ filament_diameter: 1.750 max_extrude_only_velocity: 60 max_extrude_only_distance: 200 nozzle_diameter: 0.4 -heater_pin: e_heater_pin +heater_pin: PA2 sensor_type: ATC Semitec 104GT-2 -sensor_pin: e_sensor_pin +sensor_pin: PF4 min_extrude_temp: 170 min_temp: 0 max_temp: 400 @@ -474,7 +438,7 @@ variable_macro_travel_speed: 100 ### Customize the defaults to your specific build ############################################################################################################# [stepper_x] -dir_pin: x_dir_pin # Add ! in front of pin name to reverse X stepper direction +dir_pin: PF12 # Add ! in front of pin name to reverse X stepper direction rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys position_endstop: 0 # Adjust this to your setup #x_offset: -27.0 @@ -482,7 +446,7 @@ position_endstop: 0 # Adjust this to your setup [stepper_y] -dir_pin: y_dir_pin # Add ! in front of pin name to reverse Y stepper direction +dir_pin: PG1 # Add ! in front of pin name to reverse Y stepper direction rotation_distance: 40 # 40 for 20 tooth 2GT pulleys, 32 for 16 tooth 2GT pulleys position_endstop: 480 # 300mm printer position_min: 5 @@ -493,17 +457,17 @@ position_min: 5 #position_endstop: 500 # 500mm printer [stepper_z] -dir_pin: !z0_dir_pin # Add ! in front of pin name to reverse Z stepper direction +dir_pin: !PF0 # Add ! in front of pin name to reverse Z stepper direction rotation_distance: 4 # 4 for TR8*4 lead screws endstop_pin: probe: z_virtual_endstop [stepper_z1] -dir_pin: !z1_dir_pin # Add ! in front of pin name to reverse Z1 direction +dir_pin: !PE3 # Add ! in front of pin name to reverse Z1 direction rotation_distance: 4 # 4 for TR8*4 lead screws endstop_pin: probe: z_virtual_endstop [stepper_z2] -dir_pin: !z2_dir_pin # Add ! in front of pin name to reverse Z2 direction +dir_pin: !PA14 # Add ! in front of pin name to reverse Z2 direction rotation_distance: 4 # 4 for TR8*4 lead screws endstop_pin: probe: z_virtual_endstop @@ -520,10 +484,10 @@ pin_move_time: 0.8 # [probe] # z_offset: 1.0 # Adjust this to fit your setup -> "1.0" is placeholder! -# pin: ^probe_pin # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes. -#pin: ^!probe_pin # NPN NO (refer to the specs on your probe) -#pin: probe_pin # PNP NO (refer to the specs on your probe) -#pin: !probe_pin # PNP NC (refer to the specs on your probe) +# pin: ^PB7 # For NPN NC probes such as the Super Pinda / Vinda / SupCR / Decoprobe probes. +#pin: ^!PB7 # NPN NO (refer to the specs on your probe) +#pin: PB7 # PNP NO (refer to the specs on your probe) +#pin: !PB7 # PNP NC (refer to the specs on your probe) # Safe Z Home (Physical endstops only) [safe_z_home] @@ -541,18 +505,12 @@ z_hop_speed: 5 # Check https://www.klipper3d.org/Pressure_Advance.html for pressure advance tuning. #pressure_advance: 0.05 nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter. -dir_pin: e_dir_pin # Remove ! in front of pin name to reverse extruder direction +dir_pin: PG3 # Remove ! in front of pin name to reverse extruder direction #control: pid #pid_kp: 28.413 #pid_ki: 1.334 #pid_kd: 151.300 -[heater_bed] -#control: pid -#pid_Kp: 22.2 -#pid_Ki: 1.08 -#pid_Kd: 114 - # [bed_mesh] # speed: 30