diff --git a/printer-20230131_114558.cfg b/printer-20230131_114558.cfg
new file mode 100644
index 0000000..4e35931
--- /dev/null
+++ b/printer-20230131_114558.cfg
@@ -0,0 +1,414 @@
+# Rat Rig V-core 3 Klipper Config
+# Documentation: https://os.ratrig.com
+
+# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
+# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
+# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
+# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
+
+# Read more about klipper here: https://www.klipper3d.org/Overview.html
+[include mainsail.conf]
+
+[mcu]
+baud: 250000
+serial: /dev/btt-octopus-11
+
+[temperature_sensor Octopus]
+sensor_type: temperature_mcu
+min_temp: 0
+max_temp: 100
+
+[temperature_sensor raspberry_pi]
+sensor_type: temperature_host
+
+[adxl345]
+spi_bus: spi3
+cs_pin: PA15
+
+#############################################################################################################
+### BASE SETUP
+#############################################################################################################
+[idle_timeout]
+gcode:
+  {% if printer.webhooks.state|lower == 'ready' %}
+    {% if printer.pause_resume.is_paused|lower == 'false' %}
+      M117 Idle timeout reached
+      TURN_OFF_HEATERS
+      M84
+    {% endif %}
+  {% endif %}
+# 2 hour timeout
+timeout: 7200
+
+[skew_correction]
+
+[input_shaper]
+
+[virtual_sdcard]
+path: ~/gcode_files
+
+[display_status]
+
+[pause_resume]
+
+[force_move]
+enable_force_move: True
+
+[respond]
+
+[heater_bed]
+heater_pin: PA1
+sensor_pin: PF3
+sensor_type: Generic 3950
+min_temp: 0
+max_temp: 120
+pwm_cycle_time: 0.02 # 50hz for european AC, to avoid flickering lights.
+
+[fan]
+pin: PA8
+shutdown_speed: 1.0
+
+[heater_fan toolhead_cooling_fan]
+pin: PE5
+fan_speed: 1
+
+[controller_fan controller_fan]
+pin: PD12
+
+# These are only safeguards for first time users
+# Modify printer.cfg to tune acceleration.
+[printer]
+kinematics: corexy
+max_velocity: 150
+max_accel: 500
+max_accel_to_decel: 750
+max_z_velocity: 15
+max_z_accel: 20
+
+#############################################################################################################
+### STEPPER MOTORS, DRIVERS & SPEED LIMITS
+### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
+#############################################################################################################
+[stepper_x]
+enable_pin: !PF14
+dir_pin: PF12
+step_pin: PF13
+endstop_pin: PG6
+position_endstop: 0 # Adjust this to your setup
+position_max: 500
+rotation_distance: 40
+microsteps: 64
+homing_speed: 50
+homing_retract_dist: 5.0
+
+[stepper_y]
+enable_pin: !PF15
+step_pin: PG0
+endstop_pin: PG9
+dir_pin: PG1
+position_min: 5
+position_endstop: 495
+position_max: 495
+rotation_distance: 40
+microsteps: 64
+homing_speed: 50
+homing_positive_dir: true
+homing_retract_dist: 5.0
+
+[stepper_z]
+endstop_pin: probe:z_virtual_endstop
+enable_pin: !PF1
+step_pin: PC13
+dir_pin: !PF0 # Add ! in front of pin name to reverse Z stepper direction
+rotation_distance: 4
+microsteps: 64
+position_min: -5 # Needed for z-offset calibration and tilt_adjust.
+homing_speed: 10
+position_max: 500
+
+[stepper_z1]
+endstop_pin: probe: z_virtual_endstop
+enable_pin: !PD4
+step_pin: PE2
+dir_pin: !PE3 # Add ! in front of pin name to reverse Z1 direction
+rotation_distance: 4
+microsteps: 64
+
+[stepper_z2]
+endstop_pin: probe: z_virtual_endstop
+enable_pin: !PE0
+step_pin: PE6
+dir_pin: !PA14 # Add ! in front of pin name to reverse Z2 direction
+rotation_distance: 4
+microsteps: 64
+rotation_distance: 4 # 4 for TR8*4 lead screws
+
+[z_tilt]
+speed: 200
+
+[printer]
+max_velocity: 200
+max_accel: 1500
+max_accel_to_decel: 750
+max_z_velocity: 15
+max_z_accel: 30
+square_corner_velocity: 5
+
+# Backwards compatibility
+
+[tmc2209 stepper_x]
+uart_pin: PC4
+run_current: 1.1
+stealthchop_threshold: 1
+driver_TBL: 1
+driver_TOFF: 3
+driver_HEND: 0
+driver_HSTRT: 0
+
+[tmc2209 stepper_y]
+uart_pin: PD11
+run_current: 1.1
+stealthchop_threshold: 1
+driver_TBL: 1
+driver_TOFF: 3
+driver_HEND: 0
+driver_HSTRT: 0
+
+[tmc2209 stepper_z]
+uart_pin: PE4
+run_current: 1.0
+stealthchop_threshold: 1
+driver_TBL: 1
+driver_TOFF: 3
+driver_HEND: 0
+driver_HSTRT: 0
+
+[tmc2209 stepper_z1]
+uart_pin: PE1
+run_current: 1.1
+stealthchop_threshold: 1
+driver_TBL: 1
+driver_TOFF: 3
+driver_HEND: 0
+driver_HSTRT: 0
+
+[tmc2209 stepper_z2]
+uart_pin: PD3
+run_current: 1.0
+stealthchop_threshold: 1
+driver_TBL: 1
+driver_TOFF: 3
+driver_HEND: 0
+driver_HSTRT: 0
+
+[tmc2209 extruder]
+uart_pin:  PC6
+run_current: 0.35
+stealthchop_threshold: 0
+
+
+#############################################################################################################
+### HOMING
+### Pick your probe and endstops
+#############################################################################################################
+# BL Touch
+[bltouch]
+sensor_pin: ^PB7
+control_pin: PB6
+speed: 7
+pin_move_time: 0.675
+sample_retract_dist: 10
+pin_move_time: 0.8
+pin_up_reports_not_triggered: True
+pin_up_touch_mode_reports_triggered: True
+x_offset: -28
+y_offset: -13
+
+
+
+[safe_z_home]
+home_xy_position: 150, 250 # Change coordinates to the center of your print bed
+speed: 135
+speed: 50
+z_hop: 10                 # Move up 10mm
+z_hop_speed: 5
+
+
+[bed_mesh]
+horizontal_move_z: 5
+mesh_min: 15,15
+mesh_max:465,460
+probe_count: 28,13
+fade_start: 10.0
+fade_end: 100.0
+mesh_pps: 2,2
+algorithm: bicubic
+bicubic_tension: .2
+
+[z_tilt]
+z_positions:
+	0,0
+	250,500
+	500,0
+
+points:
+	60,60
+	285,470
+	460,60
+
+horizontal_move_z: 12
+retries: 10
+retry_tolerance: 0.02
+
+
+#############################################################################################################
+### extruder and hotend
+#############################################################################################################
+
+[extruder]
+step_pin: PF11
+dir_pin: PG3
+enable_pin: !PG5
+microsteps: 64
+rotation_distance: 4.63
+full_steps_per_rotation: 200
+filament_diameter: 1.750
+max_extrude_only_velocity: 60
+max_extrude_only_distance: 200
+nozzle_diameter: 0.4
+heater_pin: PA2
+sensor_type: ATC Semitec 104GT-2
+sensor_pin: PF4
+min_extrude_temp: 170
+min_temp: 0
+max_temp: 400
+pressure_advance: 0.05
+
+[firmware_retraction]
+retract_speed: 60
+unretract_extra_length: 0
+unretract_speed: 60
+retract_length: 0.5
+
+
+
+#############################################################################################################
+### MACROS
+#############################################################################################################
+[include macros.cfg]
+[include shell-macros.cfg]
+
+# Print macros. Call these from your slicer (custom g-code).
+# You can copy these to printer.cfg and modify them to your liking, or just use them as is.
+# Read more here: https://rat-rig.github.io/V-CoreOS/#/slicers
+[gcode_macro _START_PRINT_AFTER_HEATING_BED]
+gcode:
+  {% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
+  M117 Pre-heating extruder...
+  # Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
+  # Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
+  M104 S150
+  TEMPERATURE_WAIT SENSOR=extruder MINIMUM=150
+  {% endif %}
+  M117 Adjusting for tilt...
+  # Adjust bed tilt
+  Z_TILT_ADJUST
+  M117 Rehoming after tilt adjustment...
+  # Home again as Z will have changed after tilt adjustment and bed heating.
+  G28 Z
+
+
+#############################################################################################################
+### MACRO CONFIGURATION
+### Configure the behavior of RatOS macros
+#############################################################################################################
+[gcode_macro RatOS]
+# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
+# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
+# Set to False to disable
+variable_preheat_extruder: True
+# Print a prime line or blob at the end of the START_PRINT macro
+# set to "primeline" or "primeblob", or False to disable nozzle_priming.
+variable_nozzle_priming: "false"
+# Park in the back when waiting for the extruder to heat up
+# set to "front" to park in the front, or "center" to park in the center.
+variable_start_print_park_in: "center"
+# Height to park it when waiting for extruder to heat.
+variable_start_print_park_z_height: 50
+# Skew profile to load before starting the print
+# uncomment this to use your calibrated skew correction profile.
+#variable_skew_profile: "my_skew_profile"
+# Park in the back after the print has ended or was cancelled.
+# set to "front" to park in the front, or "center" to park in the center.
+variable_end_print_park_in: "back"
+# Park in the back when the print is paused.
+# set to "front" to park in the front, or "center" to park in the center.
+variable_pause_print_park_in: "back"
+# Set the speed for travel moves in RatOS Macros in mm/s.
+variable_macro_travel_speed: 100
+
+
+#ORIGINAL
+#home_xy_position: 150,150 # 300mm printer
+#home_xy_position: 200,200 # 400mm printer
+#home_xy_position: 250,250 # 500mm printer
+
+
+#############################################################################################################
+### INPUT SHAPER
+### Enable/disable input shaper calibration
+#############################################################################################################
+# Uncomment this next line if you have an ADXL345 connected to your control board
+#[include config/printers/v-core-3/input-shaper.cfg]
+
+# ADXL345 resonance testing configuration
+#[resonance_tester]
+#probe_points:
+#    150,150,20 # 300mm printer
+#    200,200,20 # 400mm printer
+#    250,250,20 # 500mm printer
+
+#*# <---------------------- SAVE_CONFIG ---------------------->
+#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
+#*#
+#*# [bltouch]
+#*# z_offset = 3.000
+#*#
+#*# [bed_mesh default]
+#*# version = 1
+#*# points =
+#*# 	  0.754375, 0.690000, 0.584375, 0.520937, 0.427500, 0.382500, 0.296875, 0.255937, 0.217187, 0.182812, 0.166562, 0.170625, 0.171250, 0.174375, 0.160000, 0.178750, 0.225937, 0.248750, 0.248750, 0.270625, 0.313125, 0.373125, 0.390937, 0.415937, 0.460625, 0.522187, 0.607187, 0.655937
+#*# 	  0.705937, 0.606250, 0.527812, 0.459062, 0.406250, 0.340000, 0.325000, 0.267500, 0.209062, 0.211875, 0.210937, 0.170937, 0.203437, 0.180000, 0.183437, 0.221250, 0.222500, 0.246875, 0.272500, 0.298437, 0.339062, 0.380000, 0.410312, 0.463750, 0.525937, 0.550937, 0.603750, 0.696875
+#*# 	  0.710312, 0.605312, 0.542812, 0.472500, 0.412812, 0.349375, 0.332812, 0.300625, 0.274062, 0.262812, 0.244062, 0.239062, 0.201875, 0.230625, 0.223125, 0.253125, 0.256562, 0.321875, 0.314062, 0.337812, 0.383125, 0.414687, 0.459062, 0.497500, 0.550312, 0.592500, 0.646562, 0.704375
+#*# 	  0.617500, 0.540625, 0.466875, 0.442500, 0.401562, 0.374375, 0.278125, 0.276875, 0.250937, 0.214375, 0.191562, 0.185937, 0.216875, 0.203437, 0.220312, 0.225312, 0.239375, 0.293125, 0.280625, 0.355937, 0.373750, 0.421562, 0.450937, 0.462187, 0.538125, 0.569062, 0.620937, 0.745000
+#*# 	  0.451562, 0.397187, 0.365312, 0.303125, 0.262812, 0.213125, 0.162187, 0.164375, 0.170937, 0.158125, 0.150000, 0.182500, 0.170625, 0.155000, 0.180000, 0.230312, 0.197187, 0.280000, 0.272187, 0.302812, 0.368437, 0.421250, 0.443750, 0.472812, 0.521562, 0.608750, 0.651562, 0.743437
+#*# 	  0.366875, 0.276562, 0.267187, 0.231875, 0.180937, 0.150312, 0.134062, 0.114062, 0.113125, 0.120937, 0.119375, 0.139062, 0.152187, 0.122500, 0.113750, 0.158125, 0.200937, 0.223437, 0.257812, 0.327500, 0.363437, 0.415625, 0.465937, 0.499375, 0.529062, 0.604375, 0.680937, 0.788125
+#*# 	  0.264062, 0.240000, 0.179687, 0.126875, 0.118125, 0.094062, 0.046250, 0.067500, 0.046875, 0.048750, 0.103437, 0.072500, 0.092500, 0.124687, 0.150312, 0.160312, 0.238125, 0.235937, 0.279687, 0.345937, 0.366875, 0.405312, 0.460937, 0.516875, 0.590937, 0.602500, 0.690625, 0.764062
+#*# 	  0.167500, 0.121875, 0.099375, 0.068750, 0.089062, 0.057812, -0.005625, -0.005625, 0.016562, -0.015938, 0.034687, 0.026250, 0.054062, 0.087812, 0.094687, 0.154375, 0.195625, 0.206875, 0.271250, 0.301875, 0.377812, 0.412500, 0.420937, 0.506250, 0.539687, 0.584687, 0.667812, 0.789375
+#*# 	  0.161562, 0.105000, 0.111875, 0.080937, 0.053125, 0.053750, 0.033437, 0.090625, 0.010312, 0.075625, 0.040312, 0.110937, 0.128437, 0.122187, 0.144687, 0.196562, 0.207500, 0.256562, 0.274375, 0.368750, 0.374062, 0.417812, 0.508125, 0.527812, 0.580000, 0.637812, 0.715000, 0.765000
+#*# 	  0.177812, 0.088437, 0.085000, 0.115625, 0.113125, 0.080000, 0.063750, 0.081250, 0.100000, 0.066875, 0.114062, 0.120312, 0.151250, 0.165000, 0.168750, 0.223750, 0.247500, 0.275937, 0.387500, 0.402187, 0.464375, 0.529062, 0.560312, 0.580625, 0.642812, 0.688125, 0.738750, 0.805937
+#*# 	  0.221875, 0.178125, 0.161250, 0.175937, 0.179687, 0.118437, 0.122187, 0.157500, 0.133437, 0.153125, 0.174687, 0.202812, 0.175312, 0.229687, 0.272500, 0.312187, 0.358750, 0.378750, 0.478125, 0.505000, 0.514687, 0.557812, 0.599687, 0.683750, 0.715625, 0.767500, 0.824687, 0.896875
+#*# 	  0.329687, 0.304062, 0.285625, 0.289062, 0.281250, 0.280625, 0.235312, 0.279375, 0.270625, 0.290625, 0.324062, 0.299062, 0.328125, 0.350000, 0.392500, 0.431562, 0.414375, 0.457812, 0.540625, 0.569062, 0.601250, 0.663750, 0.679062, 0.673437, 0.776562, 0.784375, 0.888125, 0.951250
+#*# 	  0.463125, 0.423437, 0.413750, 0.410000, 0.426875, 0.381875, 0.400312, 0.408437, 0.412500, 0.415312, 0.434062, 0.473750, 0.502187, 0.562812, 0.526875, 0.604062, 0.614687, 0.636562, 0.731562, 0.732187, 0.786562, 0.805625, 0.842812, 0.906562, 0.967500, 0.988125, 1.064062, 1.178125
+#*# tension = 0.2
+#*# min_x = 15.0
+#*# algo = bicubic
+#*# y_count = 13
+#*# mesh_y_pps = 2
+#*# min_y = 15.0
+#*# x_count = 28
+#*# max_y = 459.96
+#*# mesh_x_pps = 2
+#*# max_x = 464.82
+#*#
+#*# [extruder]
+#*# control = pid
+#*# pid_kp = 19.661
+#*# pid_ki = 0.819
+#*# pid_kd = 117.969
+#*#
+#*# [heater_bed]
+#*# control = pid
+#*# pid_kp = 64.455
+#*# pid_ki = 1.659
+#*# pid_kd = 626.020
diff --git a/printer-20230131_183857.cfg b/printer-20230131_183857.cfg
new file mode 100644
index 0000000..f03f732
--- /dev/null
+++ b/printer-20230131_183857.cfg
@@ -0,0 +1,414 @@
+# Rat Rig V-core 3 Klipper Config
+# Documentation: https://os.ratrig.com
+
+# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
+# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
+# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
+# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
+
+# Read more about klipper here: https://www.klipper3d.org/Overview.html
+[include mainsail.conf]
+
+[mcu]
+baud: 250000
+serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_btt-octopus-11-if00
+
+[temperature_sensor Octopus]
+sensor_type: temperature_mcu
+min_temp: 0
+max_temp: 100
+
+[temperature_sensor raspberry_pi]
+sensor_type: temperature_host
+
+[adxl345]
+spi_bus: spi3
+cs_pin: PA15
+
+#############################################################################################################
+### BASE SETUP
+#############################################################################################################
+[idle_timeout]
+gcode:
+  {% if printer.webhooks.state|lower == 'ready' %}
+    {% if printer.pause_resume.is_paused|lower == 'false' %}
+      M117 Idle timeout reached
+      TURN_OFF_HEATERS
+      M84
+    {% endif %}
+  {% endif %}
+# 2 hour timeout
+timeout: 7200
+
+[skew_correction]
+
+[input_shaper]
+
+[virtual_sdcard]
+path: ~/gcode_files
+
+[display_status]
+
+[pause_resume]
+
+[force_move]
+enable_force_move: True
+
+[respond]
+
+[heater_bed]
+heater_pin: PA1
+sensor_pin: PF3
+sensor_type: Generic 3950
+min_temp: 0
+max_temp: 120
+pwm_cycle_time: 0.02 # 50hz for european AC, to avoid flickering lights.
+
+[fan]
+pin: PA8
+shutdown_speed: 1.0
+
+[heater_fan toolhead_cooling_fan]
+pin: PE5
+fan_speed: 1
+
+[controller_fan controller_fan]
+pin: PD12
+
+# These are only safeguards for first time users
+# Modify printer.cfg to tune acceleration.
+[printer]
+kinematics: corexy
+max_velocity: 150
+max_accel: 500
+max_accel_to_decel: 750
+max_z_velocity: 15
+max_z_accel: 20
+
+#############################################################################################################
+### STEPPER MOTORS, DRIVERS & SPEED LIMITS
+### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
+#############################################################################################################
+[stepper_x]
+enable_pin: !PF14
+dir_pin: PF12
+step_pin: PF13
+endstop_pin: PG6
+position_endstop: 0 # Adjust this to your setup
+position_max: 500
+rotation_distance: 40
+microsteps: 64
+homing_speed: 50
+homing_retract_dist: 5.0
+
+[stepper_y]
+enable_pin: !PF15
+step_pin: PG0
+endstop_pin: PG9
+dir_pin: PG1
+position_min: 5
+position_endstop: 495
+position_max: 495
+rotation_distance: 40
+microsteps: 64
+homing_speed: 50
+homing_positive_dir: true
+homing_retract_dist: 5.0
+
+[stepper_z]
+endstop_pin: probe:z_virtual_endstop
+enable_pin: !PF1
+step_pin: PC13
+dir_pin: !PF0 # Add ! in front of pin name to reverse Z stepper direction
+rotation_distance: 4
+microsteps: 64
+position_min: -5 # Needed for z-offset calibration and tilt_adjust.
+homing_speed: 10
+position_max: 500
+
+[stepper_z1]
+endstop_pin: probe: z_virtual_endstop
+enable_pin: !PD4
+step_pin: PE2
+dir_pin: !PE3 # Add ! in front of pin name to reverse Z1 direction
+rotation_distance: 4
+microsteps: 64
+
+[stepper_z2]
+endstop_pin: probe: z_virtual_endstop
+enable_pin: !PE0
+step_pin: PE6
+dir_pin: !PA14 # Add ! in front of pin name to reverse Z2 direction
+rotation_distance: 4
+microsteps: 64
+rotation_distance: 4 # 4 for TR8*4 lead screws
+
+[z_tilt]
+speed: 200
+
+[printer]
+max_velocity: 200
+max_accel: 1500
+max_accel_to_decel: 750
+max_z_velocity: 15
+max_z_accel: 30
+square_corner_velocity: 5
+
+# Backwards compatibility
+
+[tmc2209 stepper_x]
+uart_pin: PC4
+run_current: 1.1
+stealthchop_threshold: 1
+driver_TBL: 1
+driver_TOFF: 3
+driver_HEND: 0
+driver_HSTRT: 0
+
+[tmc2209 stepper_y]
+uart_pin: PD11
+run_current: 1.1
+stealthchop_threshold: 1
+driver_TBL: 1
+driver_TOFF: 3
+driver_HEND: 0
+driver_HSTRT: 0
+
+[tmc2209 stepper_z]
+uart_pin: PE4
+run_current: 1.0
+stealthchop_threshold: 1
+driver_TBL: 1
+driver_TOFF: 3
+driver_HEND: 0
+driver_HSTRT: 0
+
+[tmc2209 stepper_z1]
+uart_pin: PE1
+run_current: 1.1
+stealthchop_threshold: 1
+driver_TBL: 1
+driver_TOFF: 3
+driver_HEND: 0
+driver_HSTRT: 0
+
+[tmc2209 stepper_z2]
+uart_pin: PD3
+run_current: 1.0
+stealthchop_threshold: 1
+driver_TBL: 1
+driver_TOFF: 3
+driver_HEND: 0
+driver_HSTRT: 0
+
+[tmc2209 extruder]
+uart_pin:  PC6
+run_current: 0.35
+stealthchop_threshold: 0
+
+
+#############################################################################################################
+### HOMING
+### Pick your probe and endstops
+#############################################################################################################
+# BL Touch
+[bltouch]
+sensor_pin: ^PB7
+control_pin: PB6
+speed: 7
+pin_move_time: 0.675
+sample_retract_dist: 10
+pin_move_time: 0.8
+pin_up_reports_not_triggered: True
+pin_up_touch_mode_reports_triggered: True
+x_offset: -28
+y_offset: -13
+
+
+
+[safe_z_home]
+home_xy_position: 150, 250 # Change coordinates to the center of your print bed
+speed: 135
+speed: 50
+z_hop: 10                 # Move up 10mm
+z_hop_speed: 5
+
+
+[bed_mesh]
+horizontal_move_z: 5
+mesh_min: 15,15
+mesh_max:465,460
+probe_count: 28,13
+fade_start: 10.0
+fade_end: 100.0
+mesh_pps: 2,2
+algorithm: bicubic
+bicubic_tension: .2
+
+[z_tilt]
+z_positions:
+	0,0
+	250,500
+	500,0
+
+points:
+	60,60
+	285,470
+	460,60
+
+horizontal_move_z: 12
+retries: 10
+retry_tolerance: 0.02
+
+
+#############################################################################################################
+### extruder and hotend
+#############################################################################################################
+
+[extruder]
+step_pin: PF11
+dir_pin: PG3
+enable_pin: !PG5
+microsteps: 64
+rotation_distance: 4.63
+full_steps_per_rotation: 200
+filament_diameter: 1.750
+max_extrude_only_velocity: 60
+max_extrude_only_distance: 200
+nozzle_diameter: 0.4
+heater_pin: PA2
+sensor_type: ATC Semitec 104GT-2
+sensor_pin: PF4
+min_extrude_temp: 170
+min_temp: 0
+max_temp: 400
+pressure_advance: 0.05
+
+[firmware_retraction]
+retract_speed: 60
+unretract_extra_length: 0
+unretract_speed: 60
+retract_length: 0.5
+
+
+
+#############################################################################################################
+### MACROS
+#############################################################################################################
+[include macros.cfg]
+[include shell-macros.cfg]
+
+# Print macros. Call these from your slicer (custom g-code).
+# You can copy these to printer.cfg and modify them to your liking, or just use them as is.
+# Read more here: https://rat-rig.github.io/V-CoreOS/#/slicers
+[gcode_macro _START_PRINT_AFTER_HEATING_BED]
+gcode:
+  {% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
+  M117 Pre-heating extruder...
+  # Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
+  # Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
+  M104 S150
+  TEMPERATURE_WAIT SENSOR=extruder MINIMUM=150
+  {% endif %}
+  M117 Adjusting for tilt...
+  # Adjust bed tilt
+  Z_TILT_ADJUST
+  M117 Rehoming after tilt adjustment...
+  # Home again as Z will have changed after tilt adjustment and bed heating.
+  G28 Z
+
+
+#############################################################################################################
+### MACRO CONFIGURATION
+### Configure the behavior of RatOS macros
+#############################################################################################################
+[gcode_macro RatOS]
+# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
+# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
+# Set to False to disable
+variable_preheat_extruder: True
+# Print a prime line or blob at the end of the START_PRINT macro
+# set to "primeline" or "primeblob", or False to disable nozzle_priming.
+variable_nozzle_priming: "false"
+# Park in the back when waiting for the extruder to heat up
+# set to "front" to park in the front, or "center" to park in the center.
+variable_start_print_park_in: "center"
+# Height to park it when waiting for extruder to heat.
+variable_start_print_park_z_height: 50
+# Skew profile to load before starting the print
+# uncomment this to use your calibrated skew correction profile.
+#variable_skew_profile: "my_skew_profile"
+# Park in the back after the print has ended or was cancelled.
+# set to "front" to park in the front, or "center" to park in the center.
+variable_end_print_park_in: "back"
+# Park in the back when the print is paused.
+# set to "front" to park in the front, or "center" to park in the center.
+variable_pause_print_park_in: "back"
+# Set the speed for travel moves in RatOS Macros in mm/s.
+variable_macro_travel_speed: 100
+
+
+#ORIGINAL
+#home_xy_position: 150,150 # 300mm printer
+#home_xy_position: 200,200 # 400mm printer
+#home_xy_position: 250,250 # 500mm printer
+
+
+#############################################################################################################
+### INPUT SHAPER
+### Enable/disable input shaper calibration
+#############################################################################################################
+# Uncomment this next line if you have an ADXL345 connected to your control board
+#[include config/printers/v-core-3/input-shaper.cfg]
+
+# ADXL345 resonance testing configuration
+#[resonance_tester]
+#probe_points:
+#    150,150,20 # 300mm printer
+#    200,200,20 # 400mm printer
+#    250,250,20 # 500mm printer
+
+#*# <---------------------- SAVE_CONFIG ---------------------->
+#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
+#*#
+#*# [bltouch]
+#*# z_offset = 2.970
+#*#
+#*# [bed_mesh default]
+#*# version = 1
+#*# points =
+#*# 	0.754375, 0.690000, 0.584375, 0.520937, 0.427500, 0.382500, 0.296875, 0.255937, 0.217187, 0.182812, 0.166562, 0.170625, 0.171250, 0.174375, 0.160000, 0.178750, 0.225937, 0.248750, 0.248750, 0.270625, 0.313125, 0.373125, 0.390937, 0.415937, 0.460625, 0.522187, 0.607187, 0.655937
+#*# 	0.705937, 0.606250, 0.527812, 0.459062, 0.406250, 0.340000, 0.325000, 0.267500, 0.209062, 0.211875, 0.210937, 0.170937, 0.203437, 0.180000, 0.183437, 0.221250, 0.222500, 0.246875, 0.272500, 0.298437, 0.339062, 0.380000, 0.410312, 0.463750, 0.525937, 0.550937, 0.603750, 0.696875
+#*# 	0.710312, 0.605312, 0.542812, 0.472500, 0.412812, 0.349375, 0.332812, 0.300625, 0.274062, 0.262812, 0.244062, 0.239062, 0.201875, 0.230625, 0.223125, 0.253125, 0.256562, 0.321875, 0.314062, 0.337812, 0.383125, 0.414687, 0.459062, 0.497500, 0.550312, 0.592500, 0.646562, 0.704375
+#*# 	0.617500, 0.540625, 0.466875, 0.442500, 0.401562, 0.374375, 0.278125, 0.276875, 0.250937, 0.214375, 0.191562, 0.185937, 0.216875, 0.203437, 0.220312, 0.225312, 0.239375, 0.293125, 0.280625, 0.355937, 0.373750, 0.421562, 0.450937, 0.462187, 0.538125, 0.569062, 0.620937, 0.745000
+#*# 	0.451562, 0.397187, 0.365312, 0.303125, 0.262812, 0.213125, 0.162187, 0.164375, 0.170937, 0.158125, 0.150000, 0.182500, 0.170625, 0.155000, 0.180000, 0.230312, 0.197187, 0.280000, 0.272187, 0.302812, 0.368437, 0.421250, 0.443750, 0.472812, 0.521562, 0.608750, 0.651562, 0.743437
+#*# 	0.366875, 0.276562, 0.267187, 0.231875, 0.180937, 0.150312, 0.134062, 0.114062, 0.113125, 0.120937, 0.119375, 0.139062, 0.152187, 0.122500, 0.113750, 0.158125, 0.200937, 0.223437, 0.257812, 0.327500, 0.363437, 0.415625, 0.465937, 0.499375, 0.529062, 0.604375, 0.680937, 0.788125
+#*# 	0.264062, 0.240000, 0.179687, 0.126875, 0.118125, 0.094062, 0.046250, 0.067500, 0.046875, 0.048750, 0.103437, 0.072500, 0.092500, 0.124687, 0.150312, 0.160312, 0.238125, 0.235937, 0.279687, 0.345937, 0.366875, 0.405312, 0.460937, 0.516875, 0.590937, 0.602500, 0.690625, 0.764062
+#*# 	0.167500, 0.121875, 0.099375, 0.068750, 0.089062, 0.057812, -0.005625, -0.005625, 0.016562, -0.015938, 0.034687, 0.026250, 0.054062, 0.087812, 0.094687, 0.154375, 0.195625, 0.206875, 0.271250, 0.301875, 0.377812, 0.412500, 0.420937, 0.506250, 0.539687, 0.584687, 0.667812, 0.789375
+#*# 	0.161562, 0.105000, 0.111875, 0.080937, 0.053125, 0.053750, 0.033437, 0.090625, 0.010312, 0.075625, 0.040312, 0.110937, 0.128437, 0.122187, 0.144687, 0.196562, 0.207500, 0.256562, 0.274375, 0.368750, 0.374062, 0.417812, 0.508125, 0.527812, 0.580000, 0.637812, 0.715000, 0.765000
+#*# 	0.177812, 0.088437, 0.085000, 0.115625, 0.113125, 0.080000, 0.063750, 0.081250, 0.100000, 0.066875, 0.114062, 0.120312, 0.151250, 0.165000, 0.168750, 0.223750, 0.247500, 0.275937, 0.387500, 0.402187, 0.464375, 0.529062, 0.560312, 0.580625, 0.642812, 0.688125, 0.738750, 0.805937
+#*# 	0.221875, 0.178125, 0.161250, 0.175937, 0.179687, 0.118437, 0.122187, 0.157500, 0.133437, 0.153125, 0.174687, 0.202812, 0.175312, 0.229687, 0.272500, 0.312187, 0.358750, 0.378750, 0.478125, 0.505000, 0.514687, 0.557812, 0.599687, 0.683750, 0.715625, 0.767500, 0.824687, 0.896875
+#*# 	0.329687, 0.304062, 0.285625, 0.289062, 0.281250, 0.280625, 0.235312, 0.279375, 0.270625, 0.290625, 0.324062, 0.299062, 0.328125, 0.350000, 0.392500, 0.431562, 0.414375, 0.457812, 0.540625, 0.569062, 0.601250, 0.663750, 0.679062, 0.673437, 0.776562, 0.784375, 0.888125, 0.951250
+#*# 	0.463125, 0.423437, 0.413750, 0.410000, 0.426875, 0.381875, 0.400312, 0.408437, 0.412500, 0.415312, 0.434062, 0.473750, 0.502187, 0.562812, 0.526875, 0.604062, 0.614687, 0.636562, 0.731562, 0.732187, 0.786562, 0.805625, 0.842812, 0.906562, 0.967500, 0.988125, 1.064062, 1.178125
+#*# tension = 0.2
+#*# min_x = 15.0
+#*# algo = bicubic
+#*# y_count = 13
+#*# mesh_y_pps = 2
+#*# min_y = 15.0
+#*# x_count = 28
+#*# max_y = 459.96
+#*# mesh_x_pps = 2
+#*# max_x = 464.82
+#*#
+#*# [extruder]
+#*# control = pid
+#*# pid_kp = 19.661
+#*# pid_ki = 0.819
+#*# pid_kd = 117.969
+#*#
+#*# [heater_bed]
+#*# control = pid
+#*# pid_kp = 64.455
+#*# pid_ki = 1.659
+#*# pid_kd = 626.020
diff --git a/printer-20230201_082027.cfg b/printer-20230201_082027.cfg
new file mode 100644
index 0000000..6583807
--- /dev/null
+++ b/printer-20230201_082027.cfg
@@ -0,0 +1,414 @@
+# Rat Rig V-core 3 Klipper Config
+# Documentation: https://os.ratrig.com
+
+# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
+# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
+# 2) Skew Correction: https://www.klipper3d.org/Skew_Correction.html
+# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
+
+# Read more about klipper here: https://www.klipper3d.org/Overview.html
+[include mainsail.conf]
+
+[mcu]
+baud: 250000
+serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_btt-octopus-11-if00
+
+[temperature_sensor Octopus]
+sensor_type: temperature_mcu
+min_temp: 0
+max_temp: 100
+
+[temperature_sensor raspberry_pi]
+sensor_type: temperature_host
+
+[adxl345]
+spi_bus: spi3
+cs_pin: PA15
+
+#############################################################################################################
+### BASE SETUP
+#############################################################################################################
+[idle_timeout]
+gcode:
+  {% if printer.webhooks.state|lower == 'ready' %}
+    {% if printer.pause_resume.is_paused|lower == 'false' %}
+      M117 Idle timeout reached
+      TURN_OFF_HEATERS
+      M84
+    {% endif %}
+  {% endif %}
+# 2 hour timeout
+timeout: 7200
+
+[skew_correction]
+
+[input_shaper]
+
+[virtual_sdcard]
+path: ~/gcode_files
+
+[display_status]
+
+[pause_resume]
+
+[force_move]
+enable_force_move: True
+
+[respond]
+
+[heater_bed]
+heater_pin: PA1
+sensor_pin: PF3
+sensor_type: Generic 3950
+min_temp: 0
+max_temp: 120
+pwm_cycle_time: 0.02 # 50hz for european AC, to avoid flickering lights.
+
+[fan]
+pin: PA8
+shutdown_speed: 1.0
+
+[heater_fan toolhead_cooling_fan]
+pin: PE5
+fan_speed: 1
+
+[controller_fan controller_fan]
+pin: PD12
+
+# These are only safeguards for first time users
+# Modify printer.cfg to tune acceleration.
+[printer]
+kinematics: corexy
+max_velocity: 150
+max_accel: 500
+max_accel_to_decel: 750
+max_z_velocity: 15
+max_z_accel: 20
+
+#############################################################################################################
+### STEPPER MOTORS, DRIVERS & SPEED LIMITS
+### Pick the drivers and stepper motors you're using. See the RatOS documentation for custom combinations.
+#############################################################################################################
+[stepper_x]
+enable_pin: !PF14
+dir_pin: PF12
+step_pin: PF13
+endstop_pin: PG6
+position_endstop: 0 # Adjust this to your setup
+position_max: 500
+rotation_distance: 40
+microsteps: 64
+homing_speed: 50
+homing_retract_dist: 5.0
+
+[stepper_y]
+enable_pin: !PF15
+step_pin: PG0
+endstop_pin: PG9
+dir_pin: PG1
+position_min: 5
+position_endstop: 495
+position_max: 495
+rotation_distance: 40
+microsteps: 64
+homing_speed: 50
+homing_positive_dir: true
+homing_retract_dist: 5.0
+
+[stepper_z]
+endstop_pin: probe:z_virtual_endstop
+enable_pin: !PF1
+step_pin: PC13
+dir_pin: !PF0 # Add ! in front of pin name to reverse Z stepper direction
+rotation_distance: 4
+microsteps: 64
+position_min: -5 # Needed for z-offset calibration and tilt_adjust.
+homing_speed: 10
+position_max: 500
+
+[stepper_z1]
+endstop_pin: probe: z_virtual_endstop
+enable_pin: !PD4
+step_pin: PE2
+dir_pin: !PE3 # Add ! in front of pin name to reverse Z1 direction
+rotation_distance: 4
+microsteps: 64
+
+[stepper_z2]
+endstop_pin: probe: z_virtual_endstop
+enable_pin: !PE0
+step_pin: PE6
+dir_pin: !PA14 # Add ! in front of pin name to reverse Z2 direction
+rotation_distance: 4
+microsteps: 64
+rotation_distance: 4 # 4 for TR8*4 lead screws
+
+[z_tilt]
+speed: 200
+
+[printer]
+max_velocity: 200
+max_accel: 1500
+max_accel_to_decel: 750
+max_z_velocity: 15
+max_z_accel: 30
+square_corner_velocity: 5
+
+# Backwards compatibility
+
+[tmc2209 stepper_x]
+uart_pin: PC4
+run_current: 1.1
+stealthchop_threshold: 1
+driver_TBL: 1
+driver_TOFF: 3
+driver_HEND: 0
+driver_HSTRT: 0
+
+[tmc2209 stepper_y]
+uart_pin: PD11
+run_current: 1.1
+stealthchop_threshold: 1
+driver_TBL: 1
+driver_TOFF: 3
+driver_HEND: 0
+driver_HSTRT: 0
+
+[tmc2209 stepper_z]
+uart_pin: PE4
+run_current: 1.0
+stealthchop_threshold: 1
+driver_TBL: 1
+driver_TOFF: 3
+driver_HEND: 0
+driver_HSTRT: 0
+
+[tmc2209 stepper_z1]
+uart_pin: PE1
+run_current: 1.1
+stealthchop_threshold: 1
+driver_TBL: 1
+driver_TOFF: 3
+driver_HEND: 0
+driver_HSTRT: 0
+
+[tmc2209 stepper_z2]
+uart_pin: PD3
+run_current: 1.0
+stealthchop_threshold: 1
+driver_TBL: 1
+driver_TOFF: 3
+driver_HEND: 0
+driver_HSTRT: 0
+
+[tmc2209 extruder]
+uart_pin:  PC6
+run_current: 0.35
+stealthchop_threshold: 0
+
+
+#############################################################################################################
+### HOMING
+### Pick your probe and endstops
+#############################################################################################################
+# BL Touch
+[bltouch]
+sensor_pin: ^PB7
+control_pin: PB6
+speed: 7
+pin_move_time: 0.675
+sample_retract_dist: 10
+pin_move_time: 0.8
+pin_up_reports_not_triggered: True
+pin_up_touch_mode_reports_triggered: True
+x_offset: -28
+y_offset: -13
+
+
+
+[safe_z_home]
+home_xy_position: 150, 250 # Change coordinates to the center of your print bed
+speed: 135
+speed: 50
+z_hop: 10                 # Move up 10mm
+z_hop_speed: 5
+
+
+[bed_mesh]
+horizontal_move_z: 5
+mesh_min: 15,15
+mesh_max:465,460
+probe_count: 28,13
+fade_start: 10.0
+fade_end: 100.0
+mesh_pps: 2,2
+algorithm: bicubic
+bicubic_tension: .2
+
+[z_tilt]
+z_positions:
+	0,0
+	250,500
+	500,0
+
+points:
+	60,60
+	285,470
+	460,60
+
+horizontal_move_z: 12
+retries: 10
+retry_tolerance: 0.02
+
+
+#############################################################################################################
+### extruder and hotend
+#############################################################################################################
+
+[extruder]
+step_pin: PF11
+dir_pin: PG3
+enable_pin: !PG5
+microsteps: 64
+rotation_distance: 4.63
+full_steps_per_rotation: 200
+filament_diameter: 1.750
+max_extrude_only_velocity: 60
+max_extrude_only_distance: 200
+nozzle_diameter: 0.4
+heater_pin: PA2
+sensor_type: ATC Semitec 104GT-2
+sensor_pin: PF4
+min_extrude_temp: 170
+min_temp: 0
+max_temp: 400
+pressure_advance: 0.05
+
+[firmware_retraction]
+retract_speed: 60
+unretract_extra_length: 0
+unretract_speed: 60
+retract_length: 0.5
+
+
+
+#############################################################################################################
+### MACROS
+#############################################################################################################
+[include macros.cfg]
+[include shell-macros.cfg]
+
+# Print macros. Call these from your slicer (custom g-code).
+# You can copy these to printer.cfg and modify them to your liking, or just use them as is.
+# Read more here: https://rat-rig.github.io/V-CoreOS/#/slicers
+[gcode_macro _START_PRINT_AFTER_HEATING_BED]
+gcode:
+  {% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
+  M117 Pre-heating extruder...
+  # Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
+  # Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
+  M104 S150
+  TEMPERATURE_WAIT SENSOR=extruder MINIMUM=200
+  {% endif %}
+  M117 Adjusting for tilt...
+  # Adjust bed tilt
+  Z_TILT_ADJUST
+  M117 Rehoming after tilt adjustment...
+  # Home again as Z will have changed after tilt adjustment and bed heating.
+  G28 Z
+
+
+#############################################################################################################
+### MACRO CONFIGURATION
+### Configure the behavior of RatOS macros
+#############################################################################################################
+[gcode_macro RatOS]
+# Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
+# Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
+# Set to False to disable
+variable_preheat_extruder: True
+# Print a prime line or blob at the end of the START_PRINT macro
+# set to "primeline" or "primeblob", or False to disable nozzle_priming.
+variable_nozzle_priming: "false"
+# Park in the back when waiting for the extruder to heat up
+# set to "front" to park in the front, or "center" to park in the center.
+variable_start_print_park_in: "center"
+# Height to park it when waiting for extruder to heat.
+variable_start_print_park_z_height: 50
+# Skew profile to load before starting the print
+# uncomment this to use your calibrated skew correction profile.
+#variable_skew_profile: "my_skew_profile"
+# Park in the back after the print has ended or was cancelled.
+# set to "front" to park in the front, or "center" to park in the center.
+variable_end_print_park_in: "back"
+# Park in the back when the print is paused.
+# set to "front" to park in the front, or "center" to park in the center.
+variable_pause_print_park_in: "back"
+# Set the speed for travel moves in RatOS Macros in mm/s.
+variable_macro_travel_speed: 100
+
+
+#ORIGINAL
+#home_xy_position: 150,150 # 300mm printer
+#home_xy_position: 200,200 # 400mm printer
+#home_xy_position: 250,250 # 500mm printer
+
+
+#############################################################################################################
+### INPUT SHAPER
+### Enable/disable input shaper calibration
+#############################################################################################################
+# Uncomment this next line if you have an ADXL345 connected to your control board
+#[include config/printers/v-core-3/input-shaper.cfg]
+
+# ADXL345 resonance testing configuration
+#[resonance_tester]
+#probe_points:
+#    150,150,20 # 300mm printer
+#    200,200,20 # 400mm printer
+#    250,250,20 # 500mm printer
+
+#*# <---------------------- SAVE_CONFIG ---------------------->
+#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
+#*#
+#*# [bltouch]
+#*# z_offset = 2.970
+#*#
+#*# [bed_mesh default]
+#*# version = 1
+#*# points =
+#*# 	  0.721562, 0.615625, 0.513437, 0.450625, 0.389375, 0.320937, 0.245625, 0.207187, 0.173437, 0.135000, 0.122812, 0.122187, 0.143750, 0.147500, 0.161875, 0.162812, 0.174375, 0.209375, 0.227500, 0.236562, 0.250312, 0.293125, 0.350312, 0.368750, 0.407187, 0.478750, 0.531562, 0.637500
+#*# 	  0.653750, 0.566250, 0.473125, 0.405000, 0.351875, 0.280937, 0.231875, 0.217500, 0.169375, 0.159062, 0.148750, 0.154062, 0.159062, 0.116875, 0.142187, 0.194375, 0.175000, 0.202187, 0.223750, 0.246250, 0.297500, 0.349062, 0.345000, 0.374687, 0.459687, 0.506562, 0.538125, 0.644375
+#*# 	  0.616875, 0.547500, 0.467187, 0.396562, 0.322187, 0.285312, 0.238437, 0.247812, 0.207500, 0.178125, 0.163437, 0.177812, 0.152500, 0.155625, 0.157812, 0.188750, 0.218437, 0.230312, 0.274375, 0.305312, 0.340000, 0.345000, 0.405000, 0.453437, 0.490937, 0.541875, 0.609062, 0.663750
+#*# 	  0.549687, 0.487812, 0.385625, 0.378125, 0.327500, 0.265312, 0.213437, 0.207187, 0.178750, 0.135937, 0.118437, 0.146250, 0.160937, 0.156250, 0.156562, 0.173125, 0.185937, 0.212500, 0.241875, 0.269687, 0.304062, 0.351562, 0.389062, 0.432812, 0.486250, 0.538437, 0.601562, 0.666875
+#*# 	  0.389375, 0.351250, 0.299375, 0.273750, 0.210625, 0.163750, 0.140937, 0.104687, 0.100625, 0.100625, 0.070000, 0.115000, 0.099687, 0.097500, 0.120937, 0.154062, 0.152500, 0.202187, 0.235937, 0.241875, 0.315312, 0.346875, 0.394062, 0.425000, 0.500625, 0.551250, 0.593750, 0.688437
+#*# 	  0.301875, 0.218750, 0.218750, 0.174375, 0.143125, 0.096250, 0.070000, 0.061562, 0.058125, 0.053125, 0.063750, 0.071250, 0.072500, 0.069375, 0.090000, 0.117187, 0.165625, 0.172500, 0.217812, 0.266250, 0.329375, 0.348125, 0.416875, 0.455625, 0.491562, 0.565625, 0.619375, 0.729687
+#*# 	  0.205937, 0.184687, 0.128750, 0.066250, 0.063437, 0.056562, -0.005938, 0.021250, -0.001875, 0.013125, 0.014687, 0.042500, 0.062500, 0.055625, 0.094375, 0.147187, 0.182500, 0.179375, 0.241875, 0.290937, 0.311875, 0.330625, 0.398750, 0.465625, 0.507500, 0.558437, 0.653437, 0.704687
+#*# 	  0.127812, 0.090312, 0.065625, -0.001250, 0.004375, -0.018438, -0.043750, -0.060625, -0.043750, -0.032500, -0.026250, -0.023125, 0.020625, 0.050937, 0.058125, 0.111875, 0.144375, 0.190625, 0.193125, 0.253437, 0.329687, 0.357812, 0.390937, 0.441250, 0.511562, 0.584687, 0.642500, 0.740000
+#*# 	  0.100312, 0.038125, 0.057500, 0.018750, 0.022187, -0.024063, -0.018438, 0.038437, -0.003125, 0.020937, 0.000312, 0.036250, 0.029687, 0.092500, 0.086250, 0.142812, 0.146875, 0.224687, 0.235625, 0.301562, 0.349062, 0.412812, 0.467812, 0.491250, 0.542187, 0.620000, 0.667500, 0.743125
+#*# 	  0.146875, 0.090000, 0.054687, 0.055000, 0.016562, 0.036250, 0.025000, 0.025000, 0.011875, 0.055937, 0.024375, 0.067187, 0.101562, 0.120312, 0.173125, 0.180937, 0.231562, 0.252187, 0.334375, 0.347500, 0.437187, 0.506875, 0.519375, 0.569062, 0.618437, 0.668750, 0.751562, 0.837187
+#*# 	  0.189062, 0.142500, 0.082187, 0.109062, 0.112812, 0.081562, 0.094062, 0.110625, 0.102500, 0.106562, 0.117812, 0.137187, 0.193750, 0.183437, 0.239375, 0.251562, 0.281562, 0.355000, 0.408437, 0.421250, 0.490312, 0.527187, 0.572812, 0.648125, 0.704062, 0.733437, 0.801875, 0.895000
+#*# 	  0.272812, 0.225625, 0.244375, 0.210000, 0.195937, 0.208437, 0.162812, 0.178125, 0.196250, 0.213125, 0.286562, 0.272500, 0.266875, 0.317812, 0.349687, 0.424687, 0.424687, 0.441562, 0.506875, 0.533125, 0.610625, 0.640937, 0.680937, 0.705937, 0.798750, 0.790312, 0.886250, 0.943750
+#*# 	  0.388125, 0.347812, 0.317500, 0.309062, 0.368125, 0.313125, 0.298750, 0.337187, 0.309062, 0.346562, 0.369375, 0.401250, 0.438125, 0.433125, 0.468437, 0.480625, 0.515000, 0.524687, 0.618750, 0.643750, 0.695312, 0.706562, 0.772812, 0.795312, 0.872812, 0.901875, 0.991875, 1.105312
+#*# tension = 0.2
+#*# min_x = 15.0
+#*# algo = bicubic
+#*# y_count = 13
+#*# mesh_y_pps = 2
+#*# min_y = 15.0
+#*# x_count = 28
+#*# max_y = 459.96
+#*# mesh_x_pps = 2
+#*# max_x = 464.82
+#*#
+#*# [extruder]
+#*# control = pid
+#*# pid_kp = 19.661
+#*# pid_ki = 0.819
+#*# pid_kd = 117.969
+#*#
+#*# [heater_bed]
+#*# control = pid
+#*# pid_kp = 64.455
+#*# pid_ki = 1.659
+#*# pid_kd = 626.020
diff --git a/printer.cfg b/printer.cfg
index 4e35931..a59a867 100644
--- a/printer.cfg
+++ b/printer.cfg
@@ -11,7 +11,7 @@
 
 [mcu]
 baud: 250000
-serial: /dev/btt-octopus-11
+serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_btt-octopus-11-if00
 
 [temperature_sensor Octopus]
 sensor_type: temperature_mcu
@@ -307,8 +307,8 @@ gcode:
   M117 Pre-heating extruder...
   # Wait for extruder to reach 150 so an inductive probe (if present) is at a predictable temp.
   # Also allows the bed heat to spread a little, and softens any plastic that might be stuck to the nozzle.
-  M104 S150
-  TEMPERATURE_WAIT SENSOR=extruder MINIMUM=150
+  M104 S200
+  TEMPERATURE_WAIT SENSOR=extruder MINIMUM=195
   {% endif %}
   M117 Adjusting for tilt...
   # Adjust bed tilt
@@ -372,24 +372,24 @@ variable_macro_travel_speed: 100
 #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
 #*#
 #*# [bltouch]
-#*# z_offset = 3.000
+#*# z_offset = 2.770
 #*#
 #*# [bed_mesh default]
 #*# version = 1
 #*# points =
-#*# 	  0.754375, 0.690000, 0.584375, 0.520937, 0.427500, 0.382500, 0.296875, 0.255937, 0.217187, 0.182812, 0.166562, 0.170625, 0.171250, 0.174375, 0.160000, 0.178750, 0.225937, 0.248750, 0.248750, 0.270625, 0.313125, 0.373125, 0.390937, 0.415937, 0.460625, 0.522187, 0.607187, 0.655937
-#*# 	  0.705937, 0.606250, 0.527812, 0.459062, 0.406250, 0.340000, 0.325000, 0.267500, 0.209062, 0.211875, 0.210937, 0.170937, 0.203437, 0.180000, 0.183437, 0.221250, 0.222500, 0.246875, 0.272500, 0.298437, 0.339062, 0.380000, 0.410312, 0.463750, 0.525937, 0.550937, 0.603750, 0.696875
-#*# 	  0.710312, 0.605312, 0.542812, 0.472500, 0.412812, 0.349375, 0.332812, 0.300625, 0.274062, 0.262812, 0.244062, 0.239062, 0.201875, 0.230625, 0.223125, 0.253125, 0.256562, 0.321875, 0.314062, 0.337812, 0.383125, 0.414687, 0.459062, 0.497500, 0.550312, 0.592500, 0.646562, 0.704375
-#*# 	  0.617500, 0.540625, 0.466875, 0.442500, 0.401562, 0.374375, 0.278125, 0.276875, 0.250937, 0.214375, 0.191562, 0.185937, 0.216875, 0.203437, 0.220312, 0.225312, 0.239375, 0.293125, 0.280625, 0.355937, 0.373750, 0.421562, 0.450937, 0.462187, 0.538125, 0.569062, 0.620937, 0.745000
-#*# 	  0.451562, 0.397187, 0.365312, 0.303125, 0.262812, 0.213125, 0.162187, 0.164375, 0.170937, 0.158125, 0.150000, 0.182500, 0.170625, 0.155000, 0.180000, 0.230312, 0.197187, 0.280000, 0.272187, 0.302812, 0.368437, 0.421250, 0.443750, 0.472812, 0.521562, 0.608750, 0.651562, 0.743437
-#*# 	  0.366875, 0.276562, 0.267187, 0.231875, 0.180937, 0.150312, 0.134062, 0.114062, 0.113125, 0.120937, 0.119375, 0.139062, 0.152187, 0.122500, 0.113750, 0.158125, 0.200937, 0.223437, 0.257812, 0.327500, 0.363437, 0.415625, 0.465937, 0.499375, 0.529062, 0.604375, 0.680937, 0.788125
-#*# 	  0.264062, 0.240000, 0.179687, 0.126875, 0.118125, 0.094062, 0.046250, 0.067500, 0.046875, 0.048750, 0.103437, 0.072500, 0.092500, 0.124687, 0.150312, 0.160312, 0.238125, 0.235937, 0.279687, 0.345937, 0.366875, 0.405312, 0.460937, 0.516875, 0.590937, 0.602500, 0.690625, 0.764062
-#*# 	  0.167500, 0.121875, 0.099375, 0.068750, 0.089062, 0.057812, -0.005625, -0.005625, 0.016562, -0.015938, 0.034687, 0.026250, 0.054062, 0.087812, 0.094687, 0.154375, 0.195625, 0.206875, 0.271250, 0.301875, 0.377812, 0.412500, 0.420937, 0.506250, 0.539687, 0.584687, 0.667812, 0.789375
-#*# 	  0.161562, 0.105000, 0.111875, 0.080937, 0.053125, 0.053750, 0.033437, 0.090625, 0.010312, 0.075625, 0.040312, 0.110937, 0.128437, 0.122187, 0.144687, 0.196562, 0.207500, 0.256562, 0.274375, 0.368750, 0.374062, 0.417812, 0.508125, 0.527812, 0.580000, 0.637812, 0.715000, 0.765000
-#*# 	  0.177812, 0.088437, 0.085000, 0.115625, 0.113125, 0.080000, 0.063750, 0.081250, 0.100000, 0.066875, 0.114062, 0.120312, 0.151250, 0.165000, 0.168750, 0.223750, 0.247500, 0.275937, 0.387500, 0.402187, 0.464375, 0.529062, 0.560312, 0.580625, 0.642812, 0.688125, 0.738750, 0.805937
-#*# 	  0.221875, 0.178125, 0.161250, 0.175937, 0.179687, 0.118437, 0.122187, 0.157500, 0.133437, 0.153125, 0.174687, 0.202812, 0.175312, 0.229687, 0.272500, 0.312187, 0.358750, 0.378750, 0.478125, 0.505000, 0.514687, 0.557812, 0.599687, 0.683750, 0.715625, 0.767500, 0.824687, 0.896875
-#*# 	  0.329687, 0.304062, 0.285625, 0.289062, 0.281250, 0.280625, 0.235312, 0.279375, 0.270625, 0.290625, 0.324062, 0.299062, 0.328125, 0.350000, 0.392500, 0.431562, 0.414375, 0.457812, 0.540625, 0.569062, 0.601250, 0.663750, 0.679062, 0.673437, 0.776562, 0.784375, 0.888125, 0.951250
-#*# 	  0.463125, 0.423437, 0.413750, 0.410000, 0.426875, 0.381875, 0.400312, 0.408437, 0.412500, 0.415312, 0.434062, 0.473750, 0.502187, 0.562812, 0.526875, 0.604062, 0.614687, 0.636562, 0.731562, 0.732187, 0.786562, 0.805625, 0.842812, 0.906562, 0.967500, 0.988125, 1.064062, 1.178125
+#*# 	0.721562, 0.615625, 0.513437, 0.450625, 0.389375, 0.320937, 0.245625, 0.207187, 0.173437, 0.135000, 0.122812, 0.122187, 0.143750, 0.147500, 0.161875, 0.162812, 0.174375, 0.209375, 0.227500, 0.236562, 0.250312, 0.293125, 0.350312, 0.368750, 0.407187, 0.478750, 0.531562, 0.637500
+#*# 	0.653750, 0.566250, 0.473125, 0.405000, 0.351875, 0.280937, 0.231875, 0.217500, 0.169375, 0.159062, 0.148750, 0.154062, 0.159062, 0.116875, 0.142187, 0.194375, 0.175000, 0.202187, 0.223750, 0.246250, 0.297500, 0.349062, 0.345000, 0.374687, 0.459687, 0.506562, 0.538125, 0.644375
+#*# 	0.616875, 0.547500, 0.467187, 0.396562, 0.322187, 0.285312, 0.238437, 0.247812, 0.207500, 0.178125, 0.163437, 0.177812, 0.152500, 0.155625, 0.157812, 0.188750, 0.218437, 0.230312, 0.274375, 0.305312, 0.340000, 0.345000, 0.405000, 0.453437, 0.490937, 0.541875, 0.609062, 0.663750
+#*# 	0.549687, 0.487812, 0.385625, 0.378125, 0.327500, 0.265312, 0.213437, 0.207187, 0.178750, 0.135937, 0.118437, 0.146250, 0.160937, 0.156250, 0.156562, 0.173125, 0.185937, 0.212500, 0.241875, 0.269687, 0.304062, 0.351562, 0.389062, 0.432812, 0.486250, 0.538437, 0.601562, 0.666875
+#*# 	0.389375, 0.351250, 0.299375, 0.273750, 0.210625, 0.163750, 0.140937, 0.104687, 0.100625, 0.100625, 0.070000, 0.115000, 0.099687, 0.097500, 0.120937, 0.154062, 0.152500, 0.202187, 0.235937, 0.241875, 0.315312, 0.346875, 0.394062, 0.425000, 0.500625, 0.551250, 0.593750, 0.688437
+#*# 	0.301875, 0.218750, 0.218750, 0.174375, 0.143125, 0.096250, 0.070000, 0.061562, 0.058125, 0.053125, 0.063750, 0.071250, 0.072500, 0.069375, 0.090000, 0.117187, 0.165625, 0.172500, 0.217812, 0.266250, 0.329375, 0.348125, 0.416875, 0.455625, 0.491562, 0.565625, 0.619375, 0.729687
+#*# 	0.205937, 0.184687, 0.128750, 0.066250, 0.063437, 0.056562, -0.005938, 0.021250, -0.001875, 0.013125, 0.014687, 0.042500, 0.062500, 0.055625, 0.094375, 0.147187, 0.182500, 0.179375, 0.241875, 0.290937, 0.311875, 0.330625, 0.398750, 0.465625, 0.507500, 0.558437, 0.653437, 0.704687
+#*# 	0.127812, 0.090312, 0.065625, -0.001250, 0.004375, -0.018438, -0.043750, -0.060625, -0.043750, -0.032500, -0.026250, -0.023125, 0.020625, 0.050937, 0.058125, 0.111875, 0.144375, 0.190625, 0.193125, 0.253437, 0.329687, 0.357812, 0.390937, 0.441250, 0.511562, 0.584687, 0.642500, 0.740000
+#*# 	0.100312, 0.038125, 0.057500, 0.018750, 0.022187, -0.024063, -0.018438, 0.038437, -0.003125, 0.020937, 0.000312, 0.036250, 0.029687, 0.092500, 0.086250, 0.142812, 0.146875, 0.224687, 0.235625, 0.301562, 0.349062, 0.412812, 0.467812, 0.491250, 0.542187, 0.620000, 0.667500, 0.743125
+#*# 	0.146875, 0.090000, 0.054687, 0.055000, 0.016562, 0.036250, 0.025000, 0.025000, 0.011875, 0.055937, 0.024375, 0.067187, 0.101562, 0.120312, 0.173125, 0.180937, 0.231562, 0.252187, 0.334375, 0.347500, 0.437187, 0.506875, 0.519375, 0.569062, 0.618437, 0.668750, 0.751562, 0.837187
+#*# 	0.189062, 0.142500, 0.082187, 0.109062, 0.112812, 0.081562, 0.094062, 0.110625, 0.102500, 0.106562, 0.117812, 0.137187, 0.193750, 0.183437, 0.239375, 0.251562, 0.281562, 0.355000, 0.408437, 0.421250, 0.490312, 0.527187, 0.572812, 0.648125, 0.704062, 0.733437, 0.801875, 0.895000
+#*# 	0.272812, 0.225625, 0.244375, 0.210000, 0.195937, 0.208437, 0.162812, 0.178125, 0.196250, 0.213125, 0.286562, 0.272500, 0.266875, 0.317812, 0.349687, 0.424687, 0.424687, 0.441562, 0.506875, 0.533125, 0.610625, 0.640937, 0.680937, 0.705937, 0.798750, 0.790312, 0.886250, 0.943750
+#*# 	0.388125, 0.347812, 0.317500, 0.309062, 0.368125, 0.313125, 0.298750, 0.337187, 0.309062, 0.346562, 0.369375, 0.401250, 0.438125, 0.433125, 0.468437, 0.480625, 0.515000, 0.524687, 0.618750, 0.643750, 0.695312, 0.706562, 0.772812, 0.795312, 0.872812, 0.901875, 0.991875, 1.105312
 #*# tension = 0.2
 #*# min_x = 15.0
 #*# algo = bicubic